Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
V - 6
Section 5 - Chapter 2 - Installation
OKI OkiLAN 6020e User’s Guide
• The initial installation requires the file server to be
brought down and then back up again. This may be a
consideration when you are planning your install.
Depending on your current configuration, the following
software may also be needed:
• Printer driver installation diskettes. These diskettes
are provided with the OS/2 operating system or are
available from the printer manufacturer.
• LAN Manager or LAN Server installation diskettes.
Note: It is strongly recommended that you make
backup copies of the OS2.INI and
OS2SYS.INI files before you install the
OkiLAN 6020e. Follow the directions in your
OS/2 documentation to back up these files.
Installing the Utilities Software
Two software utilities are provided with the OkiLAN
6020e: INSTALL and OkiNet for OS/2.
Install
The INSTALL utility copies both software utilities to
your OS/2 server and registers the OKI application with
the OS2.INI file. You will need to run INSTALL one
time only.
OkiNet for OS/2
The OkiNet for OS/2 utility completes the initial
installation of the OkiLAN 6020e. In addition, you can
run the utility as needed to modify the configuration of
the OkiLAN 6020e or to view port information.
Note: The directory where OKI DLL files install,
c:\OS2\DLL, must be the first entry in the
LIBPATH command located in the
CONFIG.SYS file. When you reboot the
system, the OS/2 spooler will load the OKI
Network Printer Redirector.