Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IV - 59
Section 4 - Appendix B - Application Considerations
OKI OkiLAN 6020e User’s Guide
TCP/IP
4. The bootpd daemon transmits a response to the
OkiLAN 6020e with the IP address 192.168.42.55.
The OkiLAN 6020e will use this IP address for all
subsequent transmissions.
For these steps to work properly, at least one BOOTP
daemon (bootpd) must be running on the BOOTP
server. To test whether a BOOTP daemon is running on
the BOOTP server, use the ps command with the show
all process option within fifteen minutes of an
attempted BOOTP request. Unfortunately, the ps
options differ from one UNIX workstation to another.
Perform a man ps at the UNIX prompt to consult a
manual page on the ps command for a particular
workstation. If bootpd is not running on a workstation,
type man bootpd at the UNIX prompt to consult a
manual page on the BOOTP daemon and how to start
it.
Limitations
Often TCP/IP networks are divided into subnets.
BOOTP does not work across subnets. When installing
an OkiLAN 6020e, make sure the following criteria are
met for BOOTP to work properly.
• Both the BOOTP server and the OkiLAN 6020e
are physically attached to the same subnet.
• The IP address assigned to the OkiLAN 6020e
and the IP address of the BOOTP server belong to
the same subnet.
OR
• Your router(s) are configured to forward BOOTP
packets between the OkiLAN 6020e’s subnet and
the subnet of the host running the BOOTP server.