Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IV - 47
Section 4 - Chapter 6 - Telnet Configuration
OKI OkiLAN 6020e User’s Guide
TCP/IP
Configure Printer Type
This option enables you to indicate the printer type to
which the OkiLAN 6020e is connected. Printer choices
are:
1. Oki Data printer.
2. Custom printer.
• Language Switching Sequence - If you select
Custom Printer from the Configure Printer Type
screen, you must indicate the switching sequence to
be used for both PCL and PostScript. This is only
necessary if language switching is set to something
other than OFF.
TCP Connection Configuration (Option 7)
TCP Connection Timeout
This is used to sever network TCP/IP Connections that
are idle for more than a specified period of time
(between 1 and 3600 seconds). You can also disable
timeout checking. Under most conditions you will want
to leave this function enabled.
Raw Port Number
Set the port number where the raw port connections
will be accepted.
Download New Firmware (Option 8)
This option is provided for future product
modifications and enhancements. It requires an update
file from OKI.
CAUTION: Do NOT use this option without having
the upgrade files on hand. The OkiLAN 6020e will be
locked in download mode. This is indicated by a
flashing orange-green Status LED.
The latest firmware and utilities are available through:
• World Wide Web: http://www.okidata.com
Firmware update instructions are available with the
download file.