Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IV - 26
Section 4 - Chapter 4 - OkiNet for TCP/IP
OKI OkiLAN 6020e User’s Guide
Subnet Mask
If your network environment includes subnets, you will
want to set the subnet mask. The subnet mask must
follow the format XXX.XXX.XXX.XXX, where each
XXX is a number from 0 to 255.
The default subnet mask is 0.0.0.0. The OkiLAN 6020e
interprets a subnet mask of 0.0.0.0 or 255.255.255.255
as no subnet mask specified.
CAUTION: If you select an invalid subnet mask, you
may not be able to access the OkiLAN 6020e.
Default Gateway
If your local network is attached to other networks, you
can specify the address of your default gateway. This
gateway will be selected whenever messages need to be
sent to another network.
The gateway address must follow the format
XXX.XXX.XXX.XXX, where each XXX is a number
from 0 to 255.
CAUTION: If you select an invalid default gateway or
the default gateway becomes unavailable, the OkiLAN
6020e may not be able to communicate with non-local
networks.
WINS Server
If you are using WINS name resolution, set the address
of the WINS Server where the System Name of the
OkiLAN 6020e will be registered.
Use DHCP to Locate WINS Server
If you are using DHCP for IP address resolution, select
this option to obtain the address of the WINS Server
from the DHCP Server.