Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IV - 19
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
OKI OkiLAN 6020e User’s Guide
TCP/IP
Note: The Remote LPD implementation of the
OkiLAN 6020e does not support any UNIX
LPD input or output filters or the direct
printing of banner pages. It is possible to
configure some UNIX systems so that banner
pages and input and output filters will be
generated at the UNIX host and then sent to the
OkiLAN 6020e. (Refer to Appendix B,
Application Considerations.)
FTP Printing
FTP is a command line program used to transfer files
between computers. FTP provides commands for
opening a connection to another computer, specifying
the data type of any transfers, and sending and
receiving files. The OkiLAN 6020e supports a subset
of the FTP command set. This subset allows the FTP
user to open a connection to the OkiLAN 6020e,
specify a file transfer data type and send print files to a
Remote Print Queue Name on the OkiLAN 6020e.
The OkiLAN 6020e recognizes the following FTP
commands:
PUT Print a single file
The PUT command sends the file to
the OkiLAN 6020e. The first
parameter of the PUT command is the
name of the local file to PUT. The
second parameter of the PUT
command is the name of the file for the
remote PC. In order to print the file,
this second parameter must be a
Remote Print Queue Name. If you do
not specify the second parameter, FTP
sets the remote file name to the local
file name. This may produce
undesirable printing results.
SEND Treated the same as PUT.
MPUT Print multiple files.