9000GBS.
9000GBS.book Page ii Wednesday, December 6, 2000 10:07 AM Preface Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki assumes no responsibility for the results of errors beyond its control. Oki also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it.
9000GBS.book Page iii Wednesday, December 6, 2000 10:07 AM English Table of contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii EEC compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . ii Energy Star . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Table of contents. . . . . . . . . . . . . . . . . . . . . . . . . . . iii Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . .v Toner cartridge and image drum handling . . . .
9000GBS.book Page iv Wednesday, December 6, 2000 10:07 AM Internal hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Printer driver . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Windows 2000/NT 4.0 PostScript . . . . . . . 38 Windows 2000 PCL . . . . . . . . . . . . . . . . . . 38 Windows 98/95 PostScript . . . . . . . . . . . . . 39 Windows 98/95/NT 4.0 PCL . . . . . . . . . . . 39 Duplex unit . . . . . . .
9000GBS.book Page v Wednesday, December 6, 2000 10:07 AM English Safety instructions This printer has been carefully designed to give years of safe, reliable performance. As with all electrical equipment, however, there are a few basic precautions that should be taken to avoid personal injury or damaging the printer: • Read this setup guide carefully and save it for future reference. • Read and follow all warning and instruction labels on the printer itself. • Disconnect the printer before cleaning.
9000GBS.book Page vi Wednesday, December 6, 2000 10:07 AM • The power outlet into which the printer is connected must remain accessible at all times. • Opening any cover may expose hot surfaces. These are clearly labelled. Do NOT touch them. • Do not insert anything into the ventilation slots on the printer; you could get a shock or cause a fire. • • Aside from the routine maintenance described in this user’s guide, do not try to service the printer yourself.
9000GBS.book Page vii Wednesday, December 6, 2000 10:07 AM English • Small amounts of toner spilled on skin or clothing can be readily removed with soap and cold water. Using heated water will make removing the stain much more difficult. Emergency first aid • IF TONER IS SWALLOWED: Induce vomiting and seek medical attention. Never attempt to induce vomiting or give anything by mouth to a person who is unconscious. • IF TONER IS INHALED: Take the person to an open area for fresh air.
9000GBS.
000GBS.book Page 1 Wednesday, December 6, 2000 10:07 AM English Chapter 1 - Printer Setup Features • High speed printing: 21 page per minute LED colour printer and 26 page per minute LED monochrome printer with single pass digital technology for stunning quality, speed and reliability. • Four different models to choose from: C9200, C9200n, C9200dn and the flagship C9400. • True 1200 dpi resolution (C9400) or 600 x 1200 dpi resolution for very high quality output.
9000GBS.book Page 2 Wednesday, December 6, 2000 10:07 AM Unpacking After unpacking the printer and choosing a suitable place to put it, check that all the necessary parts are available to continue: WARNING THIS PRINTER HAS A WEIGHT OF 72 kg. DO NOT ATTEMPT TO LIFT IT ALONE. 2 1. The printer. 2. Four toner cartridges (cyan, magenta, yellow and black). 3. CD-ROM disk containing printer drivers and documentation (not illustrated). 4. Paper size indicator (not illustrated). 5.
9000GBS.book Page 3 Wednesday, December 6, 2000 10:07 AM English Printer components 1. Top cover 2. Top cover release catch. 3. Multi purpose tray (manual feed). 4. Paper support extension. 5. Side cover. 6. Paper guides. 7. Paper level indicator. 8. Paper tray. 9. Power switch. Chapter 1 - Printer Setup 10. Control panel. 11. LED heads (4of). 12. Discharge roller. 13. Fuser unit. 14. Image drum (cyan). 15. Image drum (magenta). 16. Image drum (yellow). 17. Image drum (black).
9000GBS.book Page 4 Wednesday, December 6, 2000 10:07 AM 21. USB interface connector. 18. Rear exit paper tray. 22. Parallel interface connector. 19. Power connector. 23. Optional network interface card. 20. Interfaces and option card slot.
9000GBS.book Page 5 Wednesday, December 6, 2000 10:07 AM English Control panel 1. Attention indicator (red). On indicates there is an error, but printing will continue. Flashing indicates there is an error, but printing will stop. 2. Ready indicator (green). On - ready to receive data. Flashing - processing data or error. 3. Liquid crystal display (LCD) panel. Two rows of up to 24 alphanumeric digits displaying print status, menu items in menu mode and error messages. 4. Menu button (0).
9000GBS.book Page 6 Wednesday, December 6, 2000 10:07 AM Printer location Place the printer on a flat surface large enough and strong enough to accept the size and weight of the printer. The printer has an approximate weight of 72 kg. There must be sufficient space around the printer to allow for access and printer maintenance. Setting up Before connecting this printer to a computer and power supply, the toner cartridge must be installed and paper inserted in the paper tray.
9000GBS.book Page 7 Wednesday, December 6, 2000 10:07 AM English 2. Open the top cover. 3. Remove the LED head restrainer (1) from behind the LED heads in the top cover. 4. Remove the orange transport lock (2) from behind the coloured lever (3) on top of the fuser unit. Note: To ease removal of the transport lock, it may be necessary to move the coloured lever (3) slightly. The coloured lever will return to its original position under spring loading after it has been released.
9000GBS.book Page 8 Wednesday, December 6, 2000 10:07 AM 8. Replace the four image drums into the printer making sure each image drum is installed in its correct colour location. WARNING BE CAREFUL WHEN HANDLING THE TONER CARTRIDGE. DO NOT LET TONER SPILL ON YOUR CLOTHING OR OTHER POROUS MATERIALS. CAUTION: Do not use excessive force when installing the toner cartridge. 2. Toner cartridge installation 1. 8 Shake the toner cartridges back and forth several times.
9000GBS.book Page 9 Wednesday, December 6, 2000 10:07 AM English 3. To prevent any accidental spillage of toner, hold the toner cartridge horizontally and remove the tape carefully and slowly. 4. Make sure the colours of the toner cartridge and image drum correspond. 5. Insert the toner cartridge into the image drum, left side first, engaging the drum spigot (1) in the hole (2) in the toner cartridge. 6.
9000GBS.book Page 10 Wednesday, December 6, 2000 10:07 AM Note: Do not exceed the maximum capapcity of the paper tray, which is approximately 550 sheets depending on paper weight. 5. Replace the tray in the printer. The paper level indicator provides a visual indication of how much paper is left in the tray. 3. The printer goes through its initialisation and warm up sequence.
9000GBS.book Page 11 Wednesday, December 6, 2000 10:07 AM English Switching off Menu settings Note 1: Never turn the printer off while it is printing. Note 2: If the optional hard disk has been fitted, The following procedure MUST BE followed before turning off to protect any data that is stored on the hard disk. Carry out the following to change the language that is displayed on the printer’s LCD. 1.
9000GBS.book Page 12 Wednesday, December 6, 2000 10:07 AM Printing Print a list of menu settings to confirm that the printer is correctly configured. 1. Make sure there is A4 size paper in the paper tray. 2. Press Menu (0) button until the INFORMATION MENU is displayed, then press Select (3) button. 3. Confirm PRINT MENU MAP is displayed on the LCD. 4. Press Select (3) button to print the menu map.
9000GBS.book Page 13 Wednesday, December 6, 2000 10:07 AM English Chapter 2 - Windows Setup Installation method The installation of the Windows printer driver and its associated software depends upon the interface connection and the Windows operating system. Note 1: Note 2: Windows NT 4.0 drivers cannot be installed using Windows Plug & Play.
9000GBS.book Page 14 Wednesday, December 6, 2000 10:07 AM Parallel interface Note 1: Printer drivers are not supplied for MS-DOS or Windows NT 3.51 operating systems. Note 2: Printer drivers are not provided for Windows NT4.0 operating system installed on a computer with an ARC compatible RISC based processor (MIPS R series, Alpha, Power PC etc.). Note 3: Parallel interface cable is not included. The parallel interface cable must be bi-directional and to standard IEEE 1284-1994. Connection 1. 14 2.
9000GBS.book Page 15 Wednesday, December 6, 2000 10:07 AM English 1. When the [Found New Hardware Wizard] appears, click on [Next]. Note: If the system has already been configured once, the printer driver configures automatically and the Found New Hardware Wizard is not displayed. Please proceed to Step 9. 2. Select [Search for the best driver for my device (Recommended)] and click on [Next]. 3. Choose [Specify a location] and click on [Next]. 4.
9000GBS.book Page 16 Wednesday, December 6, 2000 10:07 AM 9. Choose [Start]-[Settings]-[Printers], then right click the printer icon and select [Set as Default Printer]. Note: If the printer icon is not displayed, configure using the Add Printer Wizard. Windows 98 or Windows Me 1. 7. Specify if a test page is to be printed or not, then click on [Next] and click on [Finish]. 8. In the [Digital Signature Not Found] window, click on [Yes]. File copying starts.
9000GBS.book Page 17 Wednesday, December 6, 2000 10:07 AM English 2. OR Choose [Search for the best driver for your device (Recommended)] and click on [Next]. 3. Insert the printer software CD-ROM into the CDROM drive. 4. Uncheck [Floppy disk drive] and check [CDROM drive], then click on [Next] to install by default the PCL printer driver. OR For Windows 98 - To install another printer driver, uncheck both [Floppy disk drive] and [CDROM drive] and check [Specify a location].
9000GBS.book Page 18 Wednesday, December 6, 2000 10:07 AM (b) In the [Copy files from] field, enter D:\DRIVERS\W9598\Language for PostScript or PCL drivers (where D:\ is the drive letter of the CD-ROM) and click on [OK]. File copying starts. (c) 3. When [Add Printer Wizard] appears, click on [Next]. 4. Select [Local Printer], remove the check mark on [Automatically detect and install my Plug and Play printer] and click on [Next]. 5.
9000GBS.book Page 19 Wednesday, December 6, 2000 10:07 AM English 6. 7. 8. In the [Copy manufacturer’s files from] field, enter D:\DRIVERS\WIN2000\Language for PostScript or PCL drivers (where D:\ is the drive letter of the CD-ROM) and click on [OK]. 9. Choose the printer model and driver required and click on [Next]. Click on [Have Disk...]. After the [Install from Disk] window appears, insert the Printer Software CD-ROM disk into the CD-ROM drive.
9000GBS.book Page 20 Wednesday, December 6, 2000 10:07 AM 10. Confirm printer name and specify if the printer is to be used as default printer or not, then click on [Next]. 12. Specify if a test page is to be printed or not, then click on [Next] and click on [Finish]. 11. Specify if the printer is to be shared or not, then click on [Next]. 14. When the printer icon is displayed in the Printer folder, configuration is complete. 13. In the [Digital Signature Not Found] window, click on [Yes].
9000GBS.book Page 21 Wednesday, December 6, 2000 10:07 AM English 4. Select [Local Printer] and click on [Next]. Chapter 2 - Windows Setup 5. Click on [Have Disk...]. 6. After the [Install from Disk] window appears, insert the Printer Software CD-ROM disk into the CD-ROM drive. 7. In the [Copy files from] field, enter D:\DRIVERS\W9598\Language for PostScript or PCL drivers (where D:\ is the drive letter of the CD-ROM) and click on [OK].
9000GBS.book Page 22 Wednesday, December 6, 2000 10:07 AM 8. Choose the printer model and driver required and click on [Next]. 10. Confirm printer name and specify if the printer is to be used as default printer or not, then click on [Next]. 9. Among [Available Ports], select [LPT1:ECP Printer Port] and click on [Next]. 11. Specify if a test page is to be printed or not, then click on [Finish]. 12. When the printer icon appears in the Printer folder, configuration is complete. Windows 95 22 1.
9000GBS.book Page 23 Wednesday, December 6, 2000 10:07 AM English 3. When the [Add Printer Wizard] appears, click on [Next]. 4. Select [Local Printer] and click on [Next]. 5. 6. After the [Install from Disk] window appears, insert the Printer Software CD-ROM disk into the CD-ROM drive. 7. In the [Copy files from] field, enter D:\DRIVERS\W9598\Language for PostScript or PCL drivers (where D:\ is the drive letter of the CD-ROM) and click on [OK]. 8.
9000GBS.book Page 24 Wednesday, December 6, 2000 10:07 AM 9. Among [Available Ports], select [LPT1:ECP Printer Port] and click on [Next]. 11. Specify if a test page is to be printed or not, then click on [Finish]. 12. When the printer icon appears in the Printer folder, configuration is complete. Windows NT 4.0 Note: 10. Confirm printer name and specify if the printer is to be used as default printer or not, then click on [Next].
9000GBS.book Page 25 Wednesday, December 6, 2000 10:07 AM English 4. Among [Available Ports], select [LPT1:ECP Printer Port] and click on [Next]. Chapter 2 - Windows Setup 5. Click on [Have Disk...]. 6. After the [Install from Disk] window appears, insert the Printer Software CD-ROM disk into the CD-ROM drive. 7. In the [Copy manufacturer’s files from] field, enter D:\DRIVERS\NT40\Language for PostScript or PCL drivers (where D:\ is the drive letter of the CD-ROM) and click on [OK].
9000GBS.book Page 26 Wednesday, December 6, 2000 10:07 AM 8. Choose the printer and click on [Next]. 9. Confirm printer name and specify if the printer is to be used as default printer or not, then click on [Next]. 10. Specify if the printer is to be shared or not, then click on [Next]. 11. Specify if a test page is to be printed or not, then click on [Next], then click on [Finish]. 12. When the printer icon appears in the Printer folder, configuration is complete.
9000GBS.book Page 27 Wednesday, December 6, 2000 10:07 AM English USB interface Note: No USB interface cable is supplied with the printer. Please use a USB interface cable that is compatible with USB specification 1.1. General A USB interface has the following restrictions: • Will not operate using a MS-DOS or Windows 95/3.1/NT 4.0/NT 3.51 operating system. • Will not operate using a Windows 98 operating system that has been upgraded from a Windows 95/3.1 operating system.
9000GBS.book Page 28 Wednesday, December 6, 2000 10:07 AM USB driver Note: 1. 28 2. Installation of USB driver is only required for Windows 98. Select [Search for the best driver for my device (Recommended)] and click on [Next]. 3. After the [Add New Hardware Wizard] window appears, click on [Next]. Insert the printer software CD-ROM disk into the CD-ROM drive. 4. Make sure CD-ROM drive is checked and click on [Next]. 5. After Windows finds the USB driver, click on [Next]. 6.
9000GBS.book Page 29 Wednesday, December 6, 2000 10:07 AM English Plug and play configuration Windows 2000 Note: Administrator’s authority is required when installing under Windows 2000. 1. When the [Found New Hardware Wizard] appears, click on [Next]. 2. Select [Search for the best driver for my device (Recommended)] and click on [Next]. 3. Choose [Specify a location] and click on [Next]. 4. Insert the printer software CD-ROM disk into the CD-ROM drive. Chapter 2 - Windows Setup 5.
9000GBS.book Page 30 Wednesday, December 6, 2000 10:07 AM OR To install another printer driver, uncheck both [Floppy disk drive] and [CD-ROM drive] and check [Specify a location]. Enter D:\DRIVERS\WIN2000\Language (where D:\ is the drive letter of the CD-ROM), then click on [Next] selecting the required printer driver. 6. Confirm that the printer driver is ready to be installed and click on [Next]. 9.
9000GBS.book Page 31 Wednesday, December 6, 2000 10:07 AM English 2. OR Choose [Search for the best driver for your device (Recommended)] and click on [Next]. 3. Insert the Printer Software CD-ROM disk into the CD-ROM drive. 4. Uncheck [Floppy disk drive] and check [CDROM drive], then click on [Next] to install by default the PCL printer driver. For Windows ME - Select the required driver from the displayed list in order to install the language required. 5.
9000GBS.book Page 32 Wednesday, December 6, 2000 10:07 AM Add printer configuration Windows 2000 Note: Administrator’s authority is required when installing under Windows 2000. 1. Click on [Start]-[Settings]-[Printers]. 2. Double-click on [Add Printer]. 3. When the [Add Printer Wizard] appears, click on [Next]. 5. 4. 32 Select [Use the following port] and specify [USBxxx], then click on [Next].
9000GBS.book Page 33 Wednesday, December 6, 2000 10:07 AM English 6. Click on [Have Disk...]. 7. After the [Install from Disk] window appears, insert the Printer Software CD-ROM disk into the CD-ROM drive. 8. 9. Choose the printer model and driver, then click on [Next]. 10. Confirm printer name and specify if the printer is to be used as default printer or not, then click on [Next].
9000GBS.book Page 34 Wednesday, December 6, 2000 10:07 AM 11. Specify if the printer is to be shared or not, then click on [Next]. 13. In the [Digital Signature Not Found] window, click on [Yes]. File copying starts. 14. Choose [Start]-[Settings]-[Printers], then right click the printer icon and select [Set as Default Printer]. Windows 98 1. Click on [Start]-[Settings]-[Printers]. 2. Double-click on [Add Printer]. 3. When the [Add PrinterWizard] appears, click on [Next]. 12.
9000GBS.book Page 35 Wednesday, December 6, 2000 10:07 AM English 4. 5. Select [Local Printer] and click on [Next]. 6. After the [Install from Disk] window appears, insert the Printer Software CD-ROM disk into the CD-ROM drive. 7. In the [Copy files from] field, enter D:\DRIVERS\W9598\Language for PostScript or PCL drivers (where D:\ is the drive letter of the CD-ROM) and click on [OK]. 8. Choose the printer model and driver, then click on [Next]. Click on [Have Disk...].
9000GBS.book Page 36 Wednesday, December 6, 2000 10:07 AM 9. Among [Available Ports], select [OP1USBx] and click on [Next]. 11. Specify if a test page is to be printed or not, then click on [Finish]. 12. When the printer icon appears in the Printer folder, configuration is complete. 10. Confirm printer name and specify if the printer is to be used as default printer or not, then click on [Next].
9000GBS.book Page 37 Wednesday, December 6, 2000 10:07 AM English Network connection Note 1: An optional Ethernet network interface card (NIC) is needed for connection to a network. For information on installing a network interface card, refer to Chapter 8 Optional Accessories. Note 2: Administrator’s authority is required when installing using a network connection.
9000GBS.book Page 38 Wednesday, December 6, 2000 10:07 AM (b) When HDD INITIALISE is displayed, press Select (3) button. (c) Press Item (1) button to shutdown the printer. The printer has to be switched off and back on again to initialise the hard disk before use. 3. Click on [Device Settings] tab. 4. Highlight [Hard Disk], then select [Installed] and click on [OK]. Windows 2000 PCL 1. Click on [Start] - [Settings] - [Printers]. Printer driver 2.
9000GBS.book Page 39 Wednesday, December 6, 2000 10:07 AM English Windows 98/95 PostScript Windows 98/95/NT 4.0 PCL 1. Click on [Start] - [Settings] - [Printers]. 1. Click on [Start] - [Settings] - [Printers]. 2. Highlight the printer name and click on [File] then [Properties]. 2. For Windows 98/95 - Highlight the printer name and click on [File] then [Properties]. 3. Click on the [Device Options] tab. 4. Highlight [Hard Disk], then select [Installed] and click on [OK].
9000GBS.book Page 40 Wednesday, December 6, 2000 10:07 AM Duplex unit If your printer includes the duplex unit, please use the following procedure to make sure that duplex printing has been enabled in the printer and printer driver. Printer 1. Press Menu (0) button until PRINT MENU is displayed, then press Select (3) button. 2. Press Item (1) button until DUPLEX is displayed. 3. Press Value (2) button until ON is displayed and press Select (3) button.
9000GBS.book Page 41 Wednesday, December 6, 2000 10:07 AM English 3. Click on [General] tab, [Printing Preferences] button, then [Device Options] button. OR Click on [Advanced] tab, [Printing Defaults] button, then [Device Options] button.. 4. Check [Duplex Option Unit] and click on [OK] three times. Windows 98/95 PostScript 4. Highlight [Duplex], then select [Installed] and click on [OK]. Windows 98/95/NT 4.0 PCL 1. Click on [Start] - [Settings] - [Printers]. 1.
9000GBS.book Page 42 Wednesday, December 6, 2000 10:07 AM 3. Click on the [Paper] tab, then the [Device Options] button. 4. Check [Duplex Option Unit] and click on [OK] twice.
9000GBS.book Page 43 Wednesday, December 6, 2000 10:07 AM English Chapter 3 - Macintosh Setup USB connection • If a USB hub is used, it is necessary to connect the USB hub directly to the computer. Operating environment • If the memory setting for the print monitor is low and depending on the document, background printing may not be able to be carried out. Increase the memory setting for the print monitor to carry out background printing without problems.
9000GBS.book Page 44 Wednesday, December 6, 2000 10:07 AM 1. Make sure the printer and computer are turned off. 2. Connect the USB interface cable into the USB port on the computer. 3. Connnect the other end of the USB interface cable to the USB connector on the printer. 4. Turn the printer on, then turn the computer on. 2. Open [Drivers] and open the required language folder. 3. Double-click on [Adobe PS Installer]. 4.
9000GBS.book Page 45 Wednesday, December 6, 2000 10:07 AM English 5. When installation of the printer driver is complete, click on [Restart] button. 6. After the computer has restarted the Adobe PS icon should appear in the Chooser. Creating desktop printer 1. In the Adobe PS Components folder at the top directory level of your hard disk, double- click on [Desktop Printer Utility]. Note: Installing Adobe PS printer driver also installs Desktop Printer Utility in the Adobe PS Components folder. 2.
9000GBS.book Page 46 Wednesday, December 6, 2000 10:07 AM 7. Note: 4. Select the PPD for the printer from the Drivers:language folder on the CD. 5. In [USB printer selection], click on [Change] button. 6. Select the printer then click on [OK]. 46 8. Click on [Create] button, enter the printer name , then click on the [Save] button. The printer icon should appear on the desktop. Close the Desktop Printer Utility.
9000GBS.book Page 47 Wednesday, December 6, 2000 10:07 AM English Network connection Printer driver installation Note 1: An optional Ethernet network interface card (NIC) is needed for connection to a network. For information on installing a network interface card, refer to Chapter 8 Optional Accessories. Either the Adobe PostScript printer driver or LaserWriter printer driver can be used. However, for the Adobe PostScript printer driver 8.7, only MacOS 8.5 or higher can be used.
9000GBS.book Page 48 Wednesday, December 6, 2000 10:07 AM 8. Click on [Create] and an icon should appear beside the printer name. 9. Close [Chooser]. Note: The printer icon should appear on the desktop. Internal hard disk If your printer includes the hard disk, please use the following procedure to make sure that the hard disk has been enabled in the printer and printer driver. Printer 1. Print a Menu Map as follows to confirm the hard disk is correctly installed.
9000GBS.book Page 49 Wednesday, December 6, 2000 10:07 AM English (b) When HDD INITIALISE is displayed, press Select (3) button. (c) Press Item (1) button to shutdown the printer. The printer has to be switched off and back on again to initialise the hard disk before use. Printer driver Macintosh USB connection 1. Drag the printer icon from the desktop into the waste bin and empty the waste bin. 2. Create a new desktop printer and the settings will be updated automatically.
9000GBS.book Page 50 Wednesday, December 6, 2000 10:07 AM Macintosh network connection 1. Open [Chooser], click on [Adobe PS] and select the printer. 2. Click on [Setup] - [Configure]. 3. Select [Duplex] from [Installable options] and then select [Installed] from the drop down list. 4. Click on [OK] button twice and close [Chooser] to complete the re-configuration of the printer driver.
9000GBS.book Page 51 Wednesday, December 6, 2000 10:07 AM English Index A M Add printer configuration . . . . . . . . . . . . . . . . . . . 18, 32 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Connection Parallel interface . . . . . . . . . . . . . . . . . . . . . . . . . .14 Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 USB interface . . . . . . . . . . . . . . . . . . . . . . . . 27, 44 Control panel . . . . . . . . . . . . . . . . . . . .
9000GBS.book Page 52 Wednesday, December 6, 2000 10:07 AM Printer Changing display language . . . . . . . . . . . . . . . . . 11 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Menu settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9000GBS.book Page 53 Wednesday, December 6, 2000 10:07 AM English OKI SYSTEMS COMPANIES Oki Systems (UK) Ltd 550 Dundee Road, Slough Trading Estate Slough, Berkshire SL1 4LE UNITED KINGDOM Tel: +44 (0) 1753 819 819 Fax: +44 (0) 1753 819 899 http://www.oki.co.uk Oki Systems (Ireland) Limited The Square Industrial Complex Tallaght, Dublin 24 EIRE Tel: +353 (01) 459 8666 Fax: +353 (01) 459 8840 http://www.oki.
9000GBS.
