OPERATING MANUAL PERMANENT FILTER IONIC AIR PURIFIER Model No.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read all instructions before using the appliance. 2. To avoid fire or shock hazard, plug the appliance with the adapter directly into an AC electrical outlet. The adapter inputs a 12V DC power into the unit. 3. Keep the cord out of heavy traffic areas.
rod should be completely dry before installing it into the unit. Figure 1 FEATURES ● ELECTROSTATIC COLLECTING ● OZONE FILTER and ACTIVATED CARBON FILTER ● POWERFUL UV LAMP ● NEGATIVE IONIZER OZONE SAFETY INSTRUCTIONS The electrostatic/ionic air purifier will produce small amounts of ozone as a by-product. This unit complies with the requirements of UL 867 for acceptable levels of ozone (less than 0.05 parts per million by volume of air circulating through the product).
GETTING STARTED 1. Select a firm level and flat location. For proper air flow, place the unit at least 3 feet (1 M) from any wall or furniture. 2. Ensure that no grills are blocked. 3. Plug the terminal of adapter into the purifier then plug the adapter directly into an AC outlet. 4. Do not lift the unit by the top cover. Always lift it by the handle on the rear of the unit. OPERATING INSTRUCTIONS (See Figure 2) 1. Ensure the collector rod is firmly seated in place and the top cover is securely latched. 2.
Figure 4 REMOVING/ CLEANING/INSTALLING THE COLLECTOR ROD (See Figure 4) ● To remove the collector rod: 1. Unplug the unit; 2. Press the release button and flip the top cover backward; (See Figure 4 and follow arrow ①) 3. Grip the collector rod handle and pull it up firmly. (See Figure 4 and follow arrow ②) ● To clean the collector rod: -- For common household particles 1. Remove the Collector Rod from the unit as described above; 2. Use a soft, damp cloth to wipe the surface of the Collector Rod; 3.
2. Use a sponge with a mild soap and water solution to wipe the collector rod from top to bottom; 3. Wipe down the collector rod with a damp cloth and ensure that no soap residue remains on the collector rod and it is completely dry. (Do not place under running water to rinse.) 4. Insert the collector rod back into the unit. 5. Clean the collector rod every week, sooner if needed. 6. Please see the FAQ section of this manual if no dust is present on your collector rod.
REMOVING/CLEANING/INSTALLING THE CARBON FILTER (See Figure 5) ● To remove the filter: 1. Unplug the unit; 2. Press the release button and flip the top cover backward; (See Figure 5 and follow arrow ①) 3. Take out the filter from top cover by pressing and gripping the spring on the filter cover. (See Figure 5 and follow arrow ②) ● To clean the filter: 1. Clean the filter with the vacuum brush attachment of your vacuum cleaner. This will remove lint and dirt from the filter; 2.
● To install the unit after cleaning the UV lamp: 1. Ensure the unit is unplugged; 2. Install the filter to the top cover as in the above INSTALLING THE FILTER; 3. Ensure the filter is flush with the surrounding surface; 4. Flip the top cover forward and securely latch in place. CLEANING AND MAINTENANCE OF THE UNIT The air purifier should be cleaned at least once every three weeks. More frequent cleaning may be required depending upon environmental conditions. 1. Turn off and unplug the unit; 2.
FREQUENTLY ASKED QUESTIONS ● Is the air purifier considered an ozone generator? - No. Ozone generators produce large amounts of ozone and the EPA considers these unsafe for household use. The air purifier electrostatically removes particles from the air and releases only trace amounts of ozone. ● What does the power setting do? - The power setting can change the cleaning power voltage of the electrostatic wires inside the unit.
ELECTRICAL SPECIFICATIONS DC12V, 600mA WARRANTY A. This limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. Please refer to your product sales page for the warranty period for your specific purchase.
manufactured parts of this product that, upon inspection by the agent, authorized personnel is shown to have failed in normal use due to defects in material or workmanship. 6. Operating this unit under conditions other than those recommended or at voltages other than the voltage indicated on the unit, or attempting to service or modify the unit, will render this WARRANTY VOID.
