MODEL# OGAL-666 OGrow Walk-in 6' x 6' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame
Grow ! r e h t e Tog Let's Thank you for purchasing the OGROW™ greenhouse Follow the assembly and safety instructions in this manual. If you have any questions, please contact our Customer Service Department • Parts List......................................... 3-4 • Side Walls....................................... 8 • Back Wall........................................ 10 • Front Wall....................................... 12 • Door Frame................................... 14 • Roof and Full Structure...
PARTS LIST PART# PART NAME PART IMAGE QTY PART# PART NAME PART IMAGE QTY 1 Corner Beam 4 17 Front Floor Bar 1 2 Front Right Roof Beam 1 18 Vent Stopper 4 3 Front Left Roof Beam 1 19 Vertical Door Rail Support 1 4 Rear Right Roof Beam 1 20 Left Door Support 1 5 Rear Left Roof Beam 1 21 Rear Horizontal Support 1 6 Right Doorway Support 1 22 Diagonal Support 6 7 Left Doorway Support 1 23 Front Horizontal Support 2 8 Rear Support Pole- Left 1 24 Top Door Bar
PARTS LIST PART# PART NAME PART IMAGE QTY. PART# PART NAME PART IMAGE QTY.
NOTICE: ! Read the entire IMPORTANT SAFETY INFORMATION section at the beginning of this document – including all text under subheadings – before set up or use of this product. PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur.
STARTING TO BUILD ! IMPORTANT: READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING: • Before you assemble this greenhouse, you must build a proper foundation. You may use your own base of bricks, concrete blocks or treated wood. Whatever foundation you use, ensure that it is square – by checking that its diagonal measurements are equal – and level, and that the greenhouse is fastened to it securely. If you have made your own base, you will need to drill through the sill of the greenhouse.
GETTING READY Construct a base first so that the greenhouse can be immediately mounted and secured when it is completed Find someone to assist you in the assembly. The work is light and should suit any able-bodied person, who can speed up and ease assembly by assisting you. Note that the construction takes time. Work slowly and methodically so that assembly is more accurate and with fewer errors; rushing only leads to needing to undo and repeat steps done erroneously.
ASSEMBLING THE GREENHOUSE PART 1 – SIDE WALLS Lay out all the parts needed for the side wall, following the layout shown below. The grooves in the support poles should be facing you. The floor bar and gutter bar should be perpendicular to the floor, with the wider end at the top. Part# Part Name Part Image Qty.
Follow the steps below to assemble the Side Walls. NOTE: Each step applies to both relevant wall supports. 10 22 43 52 43 52 34 STEP 34 STEP 1 STEP 2 10 Slide three bolts into the groove of the support poles part 10. 3 Bolt the support poles to the outside of the floor bar. Bolt the bottom of the diagonal support poles to the inside of the floor bar. 22 10 36 36 43 52 STEP 4 43 52 43 52 10 Bolt the top of the side support poles to the outside of the gutter bar.
ASSEMBLING THE GREENHOUSE PART 2 – BACK WALL Lay out all the parts needed for the back wall, following the layout shown below. Make sure that the roof beams are on the correct sides as the left and right differ; the grooves in the support poles are facing you; and that the floor bar is perpendicular to the floor, with the wider end at the top. Part# Part Name Part Image Qty.
Follow the steps below to assemble the Back Wall. NOTE: Each step applies to both relevant corners/supports. 04 8 22 1 01 43 52 13 16 16 43 52 STEP STEP 1 STEP 2 Attach the corner brackets to the corner and roof beams. Lay the bracket above the two beams and secure loosely. 43 52 3 Bolt the floor bar to the inside of the corner beams, securing at each corner. Secure the support poles to the outer side of the floor bar.
ASSEMBLING THE GREENHOUSE PART 3 – FRONT WALL Lay out all the parts needed for the front wall, besides for parts 14 and 19. Follow the same layout as for the rear wall. (The image below is the outside view, so you must lay the pieces out in mirror image to start with.) Make sure that the roof beams are on the correct sides as the left and right differ; the floor bar is perpendicular to the floor, with the wider end at the top; and that the door frame parts are below the frame parts – on the outside.
Follow the steps below to assemble the Front Wall. NOTE: Each step applies to both relevant corners/supports. 02 Note: Steps 1 - 5 follow the same steps used for the back wall. 01 43 52 13 STEP 17 STEP 1 2 Attach the corner brackets to the side and roof beams. Lay the bracket above the two beams and secure loosely.
Follow the steps below to assemble the Door Frame. Turn the assembled wall over so that the outside is now facing you, to make attaching the door frame easier. 02 02 14 12 12 14 06 STEP STEP 1 2 Slide the door rail onto the bolt heads, starting on the left until it reaches the right end of the top doorway beam. (Note: when you stand the wall up, the rail will extend on the left of the greenhouse.) When the rail is in place, tighten the two bolts.
ASSEMBLING THE GREENHOUSE PART 4 – FULL STRUCTURE AND ROOF This section completes the greenhouse frame by joining the 4 walls and completing the roof. At this stage it is best if two people work together. Collect all the parts needed for the roof and keep on the side until necessary. Part# Part Name Part Image Qty.
Follow the steps below to assemble Full Structure and Roof. 4 43 52 1 36 36 47 17 23 34 48 1 STEP STEP 1 1 2 Attach the gutter end and beam end plastic caps to the ends of the appropriate poles, covering the exposed edges for your protection. 43 52 2 STEP 43 52 Lift the walls and bolt the side floor bars to the inside of the corner beams at each corner. 3 25 Attach the ends of the gutter bars to the inside of the corner sections on the adjoining walls.
ASSEMBLING THE GREENHOUSE PART 5 – THE DOOR Lay out all the parts needed for constructing the door, following the layout shown. The open sides of parts 24, 26 and 27 should be facing down. Part Name Part# Part Image Qty.
Follow the steps below to assemble the Door. 44 20 24 31 24 27 44 20 STEP STEP 1 STEP 2 Screw through the door side supports into the top door bar, on each side. Repeat for the two center door bars. 3 Attach the bottom door bar as in step 1. Make sure that the double edge of the bar is the lower edge. Bolt the door slider to the outside of the top door bar. The curved end with the door rollers should stand above the top door bar, with the rollers visible.
ASSEMBLING THE GREENHOUSE PART 6 – THE VENTS Lay out all the parts needed for constructing the vents, following the layout shown. The greenhouse has two window vents, but instructions are for a singular vent as the procedure for installation is the same. Pay particular attention to the way that each bar should be laid, using the images for guidance. Part# Part Name Part Image Qty.
Follow the steps below to assemble the Vents. 33 33 30 30 33 30 E 30 STEP 2 Slide the vent top bar into the vent side bars, just over the outermost layer. The top bar should be positioned in the lower groove of the side bars. 32 E E STEP 1 STEP 3 30 Insert bolts into the bottom of the two vent side bars, securing loosely. Slide polycarbonate panel E into the slot between the two narrow sheets of the bars, after removing the protective film on both sides.
ASSEMBLING THE GREENHOUSE PART 17 – INSERTING THE PANELS One at a time, place each transparent panel in its place within the greenhouse frame. Remove the protective film from each side of the panel as you position it. Secure each panel with panel clips, placing a clip wherever there is a marking on the diagrams above. TO ATTACH THE PANEL CLIPS: STEP 1 Using two fingers, apply pressure to the two rounded points of the clip, positioning them under the polycarbonate panel.
INSERTING THE PANELS 1) Start by inserting the roof panels, putting the panels in place on both sides of the roof before moving forward to the next row of roof panels. 36 35 32 15 Slide the panels into the lowest groove of the top roof bar. Slide the panels below the window vents into the groove of the vent support bar. Make sure the bottom of all the roof panels are positioned below the lip of the gutter bars.
