www.kshbrands.com support@www.kshbrands.com OGAL-46A GREENHOUSE ASSEMBLY I NSTR U C T I ONS 1.888.965.
TO PREVENT INJURY, READ AND UNDERSTAND THE GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE. Notes: 1. It takes about 2-3 hours to assemble the greenhouse by 2-3 persons. 2. The UV-protected side of the sheet is covered with opal white film and must face towards the sun. 3. Remove approximately 2 inches of film from all sheet edges before installing. Removing all film immediately after the construction is completed 4. Make sure the greenhouse is located on a flat, level surface.
www.kshbrands.com support@kshbrands.com 1.888.965.
Rear Front Notes. 1. Remove approximately 5mm of film from all sheet edges before installing. Remove all film immediately after the construction completed. 2. The UV-protected side of the sheet is covered with opal white film and must face towards the sun. POLYCARBONATE PANEL SUN Opal white film PC sheet Transparent film Two sides of PC sheet are covered with thin film, one side’s film is transparent, another’s film is opal white.
Parts Image Item # Size Qty Image Item # Size ST4x10 ST4x8 www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | Parts used in this section. Image Item # Quantity Align parts K-03b, K-A02, and K-04 each at a right angle, ensuring that the grooves are on the outside. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 2.3 & 2.4 Slide one bolt each into the two outside K-05 frames and the two inside K-A03. Then place K-A15 on theinside, connecting through those bolts. 2.1 & 2.2 Insert the bolts (K-A31) in through the holes in K-03b, K-A02 & K-04, then insert K-05 and K-A03 into the bolts and tighten the nuts. Parts used in this section. Image Item # Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 3.1 Slide each of the three K-A24 panels all the way down into each section along the longer wall. 3.2 Slide top frame K-A06 over all three panels. 3.3 Secure K-A06 with nuts and bolts, but do not tighten yet. 3.4 Insert those bolts into the grooves of K-05. Parts used in this section. Image Item # Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
4. 2Sl i det hr eebol t si nt oK19,K20 ( t al l estf r amesadj acentt oyourhouse) andK09.Sl i det wobol t si nt oK10and eachoft het woK05( mi ddl eandshor t er f r amesatt hecor ner s) .
OGAL-46A ASSEMBLY INSTRUCTIONS | 5 5.1 Slide the taller K-A22 panel in the section closest to the house, opposite of the door. 5.2 Slide K-A21 into the section adjacent to the door and K-A20 to the section across from K-A21. 5.3 Slide K-06 over the top of K-A21 and opening for the door. 5.4 Slide K-07 over the top of panels K-A22 and K-A20. Insert the polycarbonate panel into relevant place. Parts used in this section. Image Item # Fix K-06 & K-07 to the walls. Quantity www.kshbrands.
OGAL-46A ASSEMBLY INSTRUCTIONS | 6.1 Connect K07 & K-A06 with K-21 by bolts and nuts. 6.2 Connect K-07 & K-09 with K-21 by bolts and nuts. 6.3 Connect K-07 & K-20 with K-23 by bolts and nuts. Parts used in this section. Image Item # Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | Parts used in this section. Image Item # Quantity 7.1 Connect K-A07 and K-07 by the bolts and nuts. NOTE: the place for the bolts. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 8 Parts used in this section. Image Item # Quantity 8.1 Slide the K-A23 window up into the corner between K-19 and K-06. Then insert the K-12 frame under the window. Connect it to the longer side with nut and bolt. www.kshbrands.com support@kshbrands.com 8.2 Insert K-17 frame to K-5 corner frame using K-21 brace and nuts and bolts. Then connect the other end of K-17 to the middle frame K-10. 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | Parts used in this section. Image Item # Quantity 9.1 Insert the two K-A04 roof frames with bolts in K-A07 and tighten with nuts. 9.2 Slide two bolts into each K-A04, and align with holes in K-A06. Secure with nuts. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 10.1 Slide longer K-A25 panels into outer sections. 10.2 Slide shorter K-A27 panel into the middle section. Parts used in this section. Image Item # Quantity www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 11 11.1.1 Insert two bolts into the grooves of K-13. 11.1.2 Align the bolts in the outer door frame K-13 with the holes in inner door frame K-12 and tighten the nuts. Parts used in this section. Image Item # Quantity 11.2 Place the top left edge of the sliding door K-08 between the top frame K-13 and middle frame K-06 and secure with nuts and bolts. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 12 12.1 Connect K-A12 to the roof with K-07 by bolts and nuts. Parts used in this section. Image Item # Quantity 12.2 & 12.3 Connect K-A11 and K-A04 with the bolts left in K-A04 and tighten the nuts. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 13 13.1 Attach the two K-A09 sides to K-A08 top and K-A10 bottom. 13.2 Secure with two K-A31 nuts and bolts in each bottom corner and one same nuts and bolts in each top corner. 13.3 Slide K-A26 window panel into the created frame. Parts used in this section. Image Item # Quantity 13.4 Attach K-A13 handle to the K-A10 bottom frame using the two K-A32 screws. www.kshbrands.com support@kshbrands.com 1.888.965.
panel panel s
OGAL-46A ASSEMBLY INSTRUCTIONS | 15 15.3 Secure door frame with nuts and bolts at bottom corners. Parts used in this section. Image Item # Quantity 15.1 & 15.2 Slide the assembled door, ensuring the pulley wheels align to the the middle notch of K-13 on top and K-03b on the bottom. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 16 Slide the window into K-A07, check details as shown above. You should be able to pivot it up and down www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | Parts used in this section. Image Item # Quantity 17.1 Drill holes into the wall of your house adjacent to the ten holes in the outer frames of the greenhouse (K-19 and K-20 at the sides and K-A07 at the top). Insert wall mounts. 17.2 Insert K-A19 wall mounts. 17.3 Screw the ten K-A19 screws into the wall mounts. www.kshbrands.com support@kshbrands.com 1.888.965.
OGAL-46A ASSEMBLY INSTRUCTIONS | 18.1 18.2 18.1 18.2 18.1 Slide the two G-P2 connectors into where F-C07 and F-C07a each joins F-06 and F07. Parts used in this section. Image 18.3 Item # 18.3 Quantity 18.2 and 18.3 Cap off F-13 with G-P3L at the left end and G-P3R at the right end. www.kshbrands.com support@kshbrands.com 1.888.965.
Advice It is not necessary but we would advise: For additional strength, you can also use some glue or tapes between the polycarbonate panel and the aluminium frame to enhance the stability. Note: Silicone sealant and glue gun are not included in our tool kit. You can buy them locally. Only use silicone sealant suitable for aluminium www.kshbrands.com support@kshbrands.com 1.888.965.
