User Manual

3
Operating Instructions and Parts Manual 24937
11/18
2018 OEMTOOLS
™
PNEUMATIC/MANUAL FLUID
EVACUATOR - 1.5 GALLON (6 L)
11. The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product, but must be
supplied by the operator.
12. For safety purposes and the prevention of damage
to expensive components, it is advised that the user
understand basic automotive repair and have a working
knowledge of automotive systems.
13. We believe the information contained herein to be
reliable. However, general technical information is
given by us without charge and the user shall employ
such information at his or her own discretion and risk.
We assume no responsibility for results or damages
incurred from the use of such information in whole or in
part. Always refer to specific instructions and technical
information supplied by vehicle manufacturer.
14. The manufacturer declines any and all responsibility
for damage to vehicles or components if said damage
is the result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
15. Used oil, antifreeze, brake fluid and transmission fluid
contain chemical compounds that can be harmful to
humans and other animals. When managed properly,
used oil may again be of beneficial use. Used oil may
be blended and recycled as a heating or industrial
fuel and also may be re-refined and made into new
lubricants. Persons who perform maintenance on their
own vehicles are responsible for managing the used
fluids in a manner that is protective of human health
and the environment and to follow all local laws and
regulations concerning their disposal.
DISPOSAL
At the end of the useful life of the Pneumatic/Manual Fluid
Evacuator, dispose of the components according to all
local, state, and federal regulations.
PURPOSE
The OEMTOOLS™ 24937 Pneumatic/Manual Fluid
Evacuator is designed for the extraction of all types
of engine, transmission and lubricating oils from cars,
motorcycles, marine engines and industrial machinery. Also
suitable for low viscosity fluid such as water or coolant.
This fluid evacuator is equipped with a Venturi for use with
shop air.
PRODUCT SPECIFICATIONS
Reservoir Capacity 1.5 Gallon (6 L)
Operation Manual/Pneumatic
Working Pressure 85 - 110 PSI
Application Lubricating Oils, ATF,
Coolant, Brake Fluid, Water,
Other Low Viscosity Fluids
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
CAUTION: This equipment is intended for professional use
only and only for the applications specified in in this manual.
CAUTION: DO NOT attempt to extract fluids at
temperatures greater than 175°F (80°C).
CAUTION: This equipment is designed for servicing
a variety of vehicles; however, differences in makes and
models may not allow this equipment to be used as
intended by the manufacturer. DO NOT attempt to force this
equipment to fit an application for which it was not designed.
CAUTION: In addition to the guidelines set by this
manual, always follow the manufacturer provided vehicle
maintenance manual prior to attempting service of any kind.
WARNING: DO NOT use this equipment with gasoline
or other flammable liquids or with fluids at temperatures
above 175°F (80°C).
WARNING: Keep away from open flames or excessive heat.
WARNING: To extract certain fluids, the vehicle
may need to be lifted. Practice extreme caution when
using lifting equipment, and ensure that the proper lifting
equipment is utilized.
WARNING: Prior to inserting the extraction hoses into
any dipstick tube/fluid reservoir, ensure that the extraction
hoses are clean of any residual fluids. This could cause
contamination, potentially leading to system failure.
WARNING: This system creates a vacuum, thus
creating pressurized fluid. While operating, ensure secure
fittings and always check the system pressure prior to
disconnecting any hose.
ASSEMBLY
The Main Extraction Reservoir is fully assembled.
1. Remove the unit and all pieces from the packaging.
2. Refer to the parts list to ensure all pieces are present.
3. Press the Main Suction Hose into the receiving hole on
the Reservoir Cap. Press in until snug against the cap.
The O-Ring will hold the Main Suction Hose in place
during operation.
4. Remove the protective cover from the Venturi and
install the Air Fitting.
5. Ensure that the Reservoir Lid is properly secured to
the Reservoir.
6. If using shop air, connect the compressed air source to
the Air Fitting installed on the Venturi.