Operation Manual

23
OCS OPERATING MANUAL
© 2002 Design, 2011 Doc. No. 12-5272-r01 (9/28/11)
• A (< 2 sec) - to toggle Set Points.
• S (< 2 sec) - to save the setting and revert to the Set U Menu.
This feature allows selection of the algorithm used for nitrogen and oxygen calculations. Refer to page 26.
Set Conserv, information includes (Fig. 50):
> Graphic CONSERV (= Conservative Factor).
> Set Point graphics ON and OFF, Arrow ( > ) icon next to the one previously saved flashing.
• A (< 2 sec) - to toggle Set Points.
• S (< 2 sec) - to save the setting and revert to the Set U Menu.
When set On, NDLs are reduced to those of the next higher 3000 foot (915 meter) Altitude. Refer to the charts in the back.
Set Glo Dura, information includes (Fig. 51):
> Graphics GLO (= Backlight) and DURATION.
> Set Point 0 (or 5, 10, 30, 60) flashing with graphic SEC.
• A (< 2 sec) - to step upward through Set Points one at a time.
• M (< 2 sec) - to step back through Set Points one at a time.
• S (< 2 sec) - to save the setting and revert to the Set U Menu.
Glo Dura (Backlight Duration) is the time the backlight will remain On after L is released.
Set Sampling, information includes (Fig. 52):
> Set Point graphics 2 SEC, 15 SEC, 30 SEC, and 60 SEC; Arrow ( > ) icon next to the one previously saved flashing.
• A (< 2 sec) - to step upward through Set Points one at a time.
• M (< 2 sec) - to step back through Set Points one at a time.
• S (< 2 sec) - to save the setting and revert to the Set U Menu.
Sampling is the rate data is sampled and stored for download to the associated PC Interface program. Refer to pages 9 & 54.
SELECT DIVE MODE
S (< 2 sec) - to access Set Dive Mode while the selection Arrow icon ( > ) is next to it on the NORM Menu
Information includes (Fig. 53):
> Graphic SEL (= Select).
> Graphics NORM MODE, GAUG MODE, and FREE MODE; Arrow ( > ) icon next to mode currently active.
• A (< 2 sec) - to step upward through selections one at a time.
• M (< 2 sec) - to step back through selections one at a time.
• S (< 2 sec) - to save the selection and access that mode's Surface Main screen.
NORM/GAUG HISTORY MODE
S (< 2 sec) - to access History 1 while the selection Arrow icon ( > ) is next to History on the NORM (or GAUG) Menu
History 1, information includes (Fig. 54):
> Graphic HIST.
> Total number dives ever recorded (up to 9999) with graphic DIVES, 0 if no dive yet.
> Total hours of EDT (dive time) ever recorded (up to 9999) with graphic Hour and Time (clock) icon, 0 if < 1 hour.
• S (< 2 sec) - to access History 2.
History 2, information includes (Fig. 55):
> Max Depth ever (up to 400 FT/120 M) with FT (or M) and MAX icons.
> Graphic HIST.
> Graphic SEA, or EL2 to EL7, highest Altitude at which a dive was conducted.
> Temperature with ° icon and graphic F (or C), lowest recorded during any dive.
• S (< 2 sec) - to revert to NORM (or GAUG) Menu.
SERIAL NUMBER
S (< 2 sec) - to access while the selection Arrow icon ( > ) is next to it on the NORM Menu.
Information includes (Fig. 56):
> Graphic SN (= Serial Number).
> OCS's factory programmed SN.
> Graphic r1A (or higher), indicating the revision level of the Firmware (OCS's operating software); followed by 01 (or
higher), indicating the revision level of the Display.
• S (< 2 sec) - to revert to the GAUG Menu if in GAUG mode; or to access Clear (reset) if NORM, refer to page 54 .
• S (2 sec) - to revert to the NORM if in NORM mode.
Fig. 50 - SET CONSERVA-
TIVE FACTOR
Fig. 51 - SET BACKLIGHT
DURATION
Fig. 52 - SET SAMPLING
RATE
Fig. 53 - SELECT DIVE
MODE
Fig. 54 - HISTORY 1
Fig. 55 - HISTORY 2
Fig. 56 - SERIAL NUMBER