User Manual EPIRB1 Pro Category 1 EPIRB English www.oceansignal.
EPIRB1 Pro USER MANUAL © 2020 Ocean Signal Ltd The technical data, information and illustrations contained in this manual were believed to be correct at the time of print. Ocean Signal Ltd reserve the right to change specifications and other information contained in this manual as part of our continual improvement process. No part of this manual may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise, without the prior permission of Ocean Signal Ltd.
EPIRB1 Pro USER MANUAL IN CASE OF EMERGENCY USE ONLY IN SITUATIONS OF GRAVE OR IMMINENT DANGER MANUAL ACTIVATION 1 Pull the pin 4 6 Break the tab 06/03/2020 2 Release the catch 5 Remove the cover 7 Lift the flap 912S-03403-01.
EPIRB1 Pro USER MANUAL 1. GENERAL 5 1.1 1.2 1.3 1.4 5 5 5 6 6 6 6 Introduction Exposure to RF Electromagnetic Energy Warnings Operating Mode 1.4.1 Automatic Release (a) 1.4.2 Manual activation on deck (b) 1.4.3 Manual activation in a life raft (c) 2. EPIRB1 PRO OVERVIEW 7 3. INSTALLATION 8 3.1 8 8 8 Location 3.1.1 Float Free Housing 3.1.2 Adapter Bracket 4. LOADING THE EPIRB1 PRO 10 5. OPERATION 11 5.1 Manual Activation 5.1.1 Deployment from the Enclosure 5.1.
EPIRB1 Pro USER MANUAL 1. GENERAL 1.1 Introduction This manual provides valuable information for the installation, operation and routine maintenance of the EPIRB1 Pro complete with the Float Free Housing. Please read this manual completely before using your EPIRB1 Pro. 1.2 Exposure to RF Electromagnetic Energy This product complies with EN62479 (EU) and RSS-102 (Canada). 1.3 Warnings ! It is a legal requirement to register your EPIRB1 Pro with your National Authority.
EPIRB1 Pro USER MANUAL 1.4 Operating Mode Your EPIRB1 Pro may be operated in a variety of modes. 1.4.1 Automatic Release Should the vessel sink the EPIRB1 Pro will automatically be released from its housing and float to the surface. Contact with the water will automatically activate the EPIRB1 Pro. 1.4.2 Manual activation on deck When deploying the EPIRB1 Pro on a deck, ensure it is vertical and clear of obstructions that might impede a clear view of the sky.
EPIRB1 Pro USER MANUAL 2. EPIRB1 PRO OVERVIEW 1) ON Key (Under flap) 2) Indicator LED 3) Break Off Tab 4) Antenna 5) Strobe light 6) TEST Key 7) Lanyard under rubber band 4 3 5 2 6 1 7 ! The lanyard is provided to attach the EPIRB1 Pro to the life raft or your person, once it is activated. Do not use it to attach it to the ship, as this may result in the loss of the EPIRB1 Pro if the vessel sinks. ! It is important that the vessel details are marked on the EPIRB1 Pro.
EPIRB1 Pro USER MANUAL 3. INSTALLATION ! Failure to follow the following installation guidelines may cause the EPIRB1 Pro to operate incorrectly. ! Do not mount the EPIRB1 Pro closer than 1.0 metre to any steering compass as this may affect the accuracy of the compass. ! Keep the EPIRB1 Pro away from any strong magnetic sources such as loudspeakers, compass compensation magnets, etc. 3.1 Location The location selected must be sufficiently robust to support the weight of the entire unit.
EPIRB1 Pro USER MANUAL 3.1.2 Retro-fit Adapter Bracket The EPIRB1 Pro Float Free Housing comes with an adapter bracket that allows easy installation where older EPIRBs from other manufacturers have been fitted. Attach the adapter bracket to the Float Free Housing using the two holes ‘A’ and the self tapping screws provided. The Adapter bracket provides fixing holes suitable for: 3.2 • J - Jotron Tron 60S • M - McMurdo E5/G5 Mounting Dimensions 06/03/2020 912S-03403-01.
EPIRB1 Pro USER MANUAL 4. LOADING THE EPIRB1 PRO ! When replacing the EPIRB1 Pro in the Float Free Housing please ensure that the unit is clean and dry. The area around the activation controls and the lanyard should be free from water and dirt to ensure reliable operation. The EPIRB1 Pro is held in place inside the Float Free Housing by the Hydrostatic Release Unit (HRU) which locks into position using a spring.
EPIRB1 Pro USER MANUAL 5 4. Place the housing cover over the back, by placing the locating holes (on the side of the housing) over the clips. 5. Push and rotate the housing release knob into the locked position (right). 6. Fold the latch up over the release knob 7. Insert the pin to retain the latch Push & Turn the knob 6 Close the catch 7 Insert the pin Complete the provided identification label using a UV stable indelible pen.
EPIRB1 Pro USER MANUAL 5. OPERATION IN CASE OF EMERGENCY USE ONLY IN SITUATIONS OF GRAVE OR IMMINENT DANGER The EPIRB1 Pro is designed for best operation while floating in water. If used in other situations ensure that the EPIRB1 Pro is placed in the open, clear of any cover and kept upright. Do not place the EPIRB1 Pro close to large structures or under cover. In the event the vessel sinks the EPIRB1 Pro will automatically be released from the housing and will activate on contact with the water.
EPIRB1 Pro USER MANUAL 5.1 Manual Activation 5.1.1 Removing from the Enclosure 1. Remove the pin 2. Release the safety catch from the release knob 3. Turn the knob anti-clockwise to release the cover 1 2 3 4. Pull the cover free and discard. 5. Lift the Hydrostatic clip and remove the EPIRB1 Pro from the mount 4 06/03/2020 5 912S-03403-01.
EPIRB1 Pro USER MANUAL 5.1.2 EPIRB1 Pro Manual Activation 1 1. Break off the red protective tab from the top of the EPIRB1 Pro. 2. Lift the yellow flap up to expose the Red ON/OFF button. 3. Press and hold the red button for 1 second to activate. (Until the green LED starts to flash) 2 3 The EPIRB1 Pro will now be operational. The strobe lights will begin to flash at a rate of once every 2.5 seconds as soon as the unit is activated.
EPIRB1 Pro USER MANUAL 5.1.3 EPIRB1 Pro Automatic Operation The EPIRB1 Pro will sense when it has been placed in water and automatically begin to operate after a short delay, in the same manner as described above. ! If the EPIRB1 Pro is mounted in the float free housing this function is disabled until the EPIRB1 Pro has been released.
EPIRB1 Pro USER MANUAL 6. FALSE ALERTS False alerts are a serious problem - they cause valuable resources to be diverted away from real emergency situations. If a false alert is initiated, by any means, it is important to contact the nearest search and rescue authority and inform them of the false alert. Report the following information: 1. 2. 3. 4. 5. EPIRB1 Pro UIN. Date, time and duration. Cause of activation. Location when the alert was activated. Location at time of deactivation.
EPIRB1 Pro USER MANUAL 7.1 Beacon Test ! Ensure the antenna is free and above the EPIRB1 Pro before commencing the test. Fold the antenna back behind the EPIRB1 Pro as you replace it in the housing. ! Because the test transmits a short burst on the aircraft distress frequency of 121.5MHz, please only carry out this test in the first five minutes of each hour. ! It is recommended to test your EPIRB1 Pro once a month.
EPIRB1 Pro USER MANUAL 7.2 GPS Test ! As testing the GPS receiver expends significant amounts of battery energy, do not test the GPS operation more than once a year. Testing the GPS receiver is limited to 12 tests over the lifetime of the battery, after this the GPS test will fail to activate. ! This test must only be performed where the EPIRB1 Pro has a clear and unobstructed view of the sky.
EPIRB1 Pro USER MANUAL 8. COSPAS/SARSAT SYSTEM The COSPAS/SARSAT system utilises two satellite arrays to provide distress alert and location data to search and rescue authorities: • The GEOSAR system can provide near immediate alerting within the coverage of the receiving satellite. The LEOSAR system provides coverage of the • polar region beyond the range of the GEOSAR system.
EPIRB1 Pro USER MANUAL 9. APPENDIX 9.1 Maintenance and Troubleshooting Your EPIRB1 Pro will require little maintenance except periodic cleaning, if required. Always use a damp cloth to clean the case and dry thoroughly. Do not use solvents or other cleaning fluids as this may cause the plastics to deteriorate. Ensure the antenna is free to unwind. ! 9.2 There are no user serviceable parts inside the EPIRB1 Pro Batteries The EPIRB1 Pro contains Lithium batteries for long operating life.
EPIRB1 Pro USER MANUAL 9.5 Specifications 406MHz Transmitter Frequency Output Power Modulation Encoding Rate 406.040 MHz ±1KHz 12W EIRP Phase ±1.1 Radians Pk (16K0G1D) Biphase L 400 bps 121.5MHz Transmitter Frequency Output Power Modulation Modulation Depth Frequency Stability Duty Cycle 121.
EPIRB1 Pro USER MANUAL 9.6 Approvals 9.6.1 Marine Equipment Directive The EPIRB1 Pro is approved under the EU Marine Equipment Directive under Annex A,1/5.6 of the current implementing regulation for carry off purposes only. The Declaration of Conformity can be downloaded from: www.oceansignal.com/products/epirb1pro. 9.6.2 Industry Canada Approval This device complies with Industry Canada licence-exempt RSS standard(s).
EPIRB1 Pro USER MANUAL 9.9 Limited Warranty Your Ocean Signal EPIRB1 Pro is warranted against manufacturing defects in materials and workmanship for a period of two years from the date of purchase and in accordance with the following conditions. Ocean Signal will at its discretion, repair or replace faulty product free of charge excluding the cost of shipping. Proof of purchase shall be required in order for a warranty claim to be valid from the original purchaser.
Ocean Signal Ltd. Unit 4, Ocivan Way Margate CT9 4NN United Kingdom info@oceansignal.com www.oceanginal.
