Calibration Light Source CAL-2000 Installation and Operation Manual Document Number 000-10000-010-02-1209 Offices: Ocean Optics, Inc. World Headquarters 830 Douglas Ave., Dunedin, FL, USA 34698 Phone 727.733.2447 Fax 727.733.3962 8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST Ocean Optics Mikropack Maybachstraße 11, D-73760, Ostfildern, Germany Phone +49 (0)711 34 16 96-0 Fax +49 (0)711 34 16 96-85 E-mail: Info@OceanOptics.com Info@Mikropack.de Orders@OceanOptics.com TechSupport@OceanOptics.
Copyright © 2009 Ocean Optics, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission from Ocean Optics, Inc. This manual is sold as part of an order and subject to the condition that it shall not, by way of trade or otherwise, be lent, re-sold, hired out or otherwise circulated without the prior consent of Ocean Optics, Inc.
Microsoft, Windows, Windows 95, Windows 98, Windows Me, Windows NT, Windows 2000, Windows XP and Excel are either registered trademarks or trademarks of Microsoft Corporation. Limit of Liability Every effort has been made to make this manual as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an “as is” basis. Ocean Optics, Inc.
Important Safety Notices 1. Do not remove or modify any installed safety device on this equipment. Doing so will void your warranty and create an unsafe operating environment. 2. Dangerous voltages are present in this device. There are NO user serviceable parts inside. 3. Only allow qualified personnel to service this unit. 4. Do not use the unit if it is damaged in any way. Contact your dealer for repair or replacement information. 5. Always screw in the fiber optic cables before starting the instrument.
Important Safety Notices B 000-10000-010-02-1209
Table of Contents About This Manual .............................................................................................................iii Document Purpose and Intended Audience.............................................................................. iii What’s New in this Document ................................................................................................... iii Document Summary..............................................................................................
Table of Contents ii 000-10000-010-02-1209
About This Manual Document Purpose and Intended Audience This document provides you with an installation section to get your system up and running. What’s New in this Document This version of the Calibration Light Source CAL2000 Installation and Operation Manual updates the logo and contact information.. Document Summary Chapter Description Chapter 1: Setup Contains a list of package contents and unpacking instructions.
About This Manual iv 000-10000-010-02-1209
Chapter 1 Setup Overview The following sections provide instructions on unpacking and setting up your CAL-2000 Calibration Light Source. Before using the CAL-2000 for the first time check for transport damage. Be sure to adhere to all warnings on the unit and in this manual.
1: Setup Unpacking the CAL-2000 ► Procedure 1. Unpack your lamp assembly carefully. Although the lamp is rigidly mounted, dropping this instrument can cause permanent damage. 2. Inspect the outside of the instrument and make sure that there is no damage. Do not use the instrument if damage is present. 3. Use this instrument in a clean laboratory environment.
Chapter 2 CAL-2000 Specifications This section provides information on the operating environment, physical controls, and dimensions of the CAL-2000. It also provides a graph of spectral lines. Operating Environment The following table provides information on optimizing the operating environment of your CAL-2000. Operating Environment The Cal-2000 Unit . . . Moisture Is designed for operation in dry rooms only.
2: Cal-2000 Specifications Front of Unit: Fiber optic SMA 905 compatible connector.
2: Cal-2000 Specifications Spectral Lines 000-10000-010-02-1209 5
2: Cal-2000 Specifications 6 000-10000-010-02-1209
Appendix A Bulb Replacement To order replacement bulbs for the CAL-2000, order item number: CAL-2000B Replacing the Bulb ► Procedure 1. Remove the four screws that secure the curved top of the CAL-2000. 2. Remove the bulb from the CAL-2000 by gently pulling the lamp out of the internal lamp socket. 3. Insert the new CAL-2000B firmly into the internal lamp socket. 4. Resecure the curved top onto the CAL-2000 with the four mounting screws.
A: Bulb Replacement 8 000-10000-010-02-1209
Index B bulb replacement, 7 D dimensions, 4 document audience, iii purpose, iii summary, iii S setup, 1 specifications, 3 spectral lines, 5 U unpacking procedure, 2 upgrades, iii O W what's new, iii operating environment, 3 P package contents, 2 product-related documentation, iii 000-10000-010-02-1209 9
Index 10 000-10000-010-02-1209
