VACUUM CLEANER USER’S MANUAL 1
WELCOME Welcome to the clean world of OceanBlue! Dear Customer: Thank you for your confidence in our product. It is our goal to bring you into the clean world of OceanBlue.
Using your Vacuum…………………………………………………………………………………………….. 14 Warranty …………………………………………………………………………………………………………….. 15 Troubleshoot ……………………………………………………………………………………………………… 16-17 OPTIONAL ACCESSORIES Prolux Storm: The Prolux Storm has incorporated an electronically driven brush roll to this universal shampoo system. This design allows the shampoo system to agitate the surface which improves cleaning ability exponentially.
TECHNICAL SPECIFICATIONS • • • • • • • • • • • • • • Durable ABS Construction 30ft power cord 120 volt 7.
GETTING TO KNOW THE PARTS 1. Power Button 2. Hose/Cord Hanger 3. Blower Output on Back 4. Water Bowl Latch 5. Friction Fit Caddy (Also Holds Tools) 6. Water Basin 7. Power Hose Plug 8. Electric Main Hose 9. Power Head Switch 10. Handle Release 11. Extendable Wand Button 12. Wand Release Pedal 13. Electric Power Nozzle 14. Rubber Bumper 15. Pivot Release 16. Suction Relief Valve 17. Tool Hose/Wet Pickup 18. Mini Turbo w/Spinning Brush roll 19. Handheld Shampoo 20. Blower/Coil Cleaner 21.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING: To reduce the risk of fire, electric shock, or injury: 1. The switch used for controlling the appliance must be pushed to start and pushed to stop. 2. This appliance is for indoor use only. Do not store in wet places. 3. This appliance is for household use only. 4.
GENERAL PRECAUTIONS & RECOMMENDATIONS IMPORTANT Please read all instructions before using this machine and keep this manual always at hand. Follow the instructions manual for the Ocean Blue‘s. Do not try to use it otherwise. The use of non-authorized accessories by OceanBlue could be dangerous. See section SERVICING OF DOUBLE INSULATED APPLIANCES. • DO NOT plug the OceanBlue into the receptacle of an incandescent light bulb, nor use extensions cords with less electrical capacity than needed.
SPECIAL CARE & SAFETY INSTRUCTIONS WATER: Do not operate the OceanBlue for too long without changing the water. When you notice that the water is getting too full of dust and fuzz, throw it away and replace it with clean water. The correct level of water is that of the height of the central post of the water container. WATER CONTAINER: When you finish cleaning your house, be careful to put away the OceanBlue‘s motor apart from the water container between uses.
HYDROTURBINE CARE 9
OPERATION AND HANDLING General guidelines for using OceanBlue: Fill up the water container with cold water until it almost covers the top of the central post: correct quantity of water 2.365 liters (2.5 quarts). (fig.1) The motor unit is placed on top of the water container (fi g.2). The air intake should be lined up with the notch in the motor unit.
WATER CONTAINER / HYDROTURBINE To empty the water container: 1. Release both clamps by pulling the upper part of the clamp assembly down and remove motor. 2. Pickup the water container by the vacuum intake end and empty the water. 3. Place the heavier particles in the bottom of the water container in a trash can (such as wet fuzz) 4. Wash, rinse and dry the water container 5. Keep the motor apart from the water container until next use.
Using The Attachments Floor Tool (Fig 1): Soft natural fill which supports the brush over hard floors and makes it easily maneuverable over uneven surfaces, without damaging the finish. It has wide cleaning opening which captures large debris and delivers effective cleaning power to the far edges of the tool. Duster Brush (Fig 2): The Dusting Brush is used for all types of furniture. Crevice Tool (Fig 3): Use for cleaning radiators, cracks & crevices along corners, and baseboards and in-between cushions.
HOSE Use to vacuum dry and wet materials on floor, walls, tapestries, electro-domestic devices, air conditioning ducts, clothes, etc. To clean and/or to dry the interior of the hose and of the stainless curved wand: 1. Remove the discharge air cover of the OceanBlue vacuum cleaner and introduce the plastic end of the hose in it as shown. 2. Then connect the other end of the hose into the vacuum air intake. Turn on the motor and shake the hose.
USING YOUR VACUUM REMEMBER THE FOLLOWING WHEN USING YOUR VACUUM CLEANER: The functioning of your new cleaning equipment greatly depends on the maintenance given at home. Only use your OceanBlue equipment according to the instructions provided in this manual. • Before using the machine pick up by hand any hard or sharp objects such as pins, hairpins, thumbtacks, pieces of pencil, etc. that could harm the spinning brush roll. • Do not lubricate the motor. The motor has permanent lubrication and is sealed.
FIVE (5) YEAR LIMITED WARRANTY (90 days on the motor and body if used commercially) OceanBlue warranties this product’s motor free from defects in material and workmanship for a period of five (5) years on the motor, and three (3) years on the body of the vacuum, free from manufacturer defects in material and workmanship from the original date of purchase, when utilized for normal household use.
Troubleshooting WARNING: Never use a defective appliance. Always switch off the appliance and disconnect it from the outlet or remove the battery before you start to troubleshoot. Fault Possible Cause(s) Solution The vacuum will not turn on. The plug is not connected to the electrical wall outlet or the appliance is not switched to the “on” position. Insert the plug into an electrical wall outlet and flip the “on/off” switch to the “on” position. See section “Vacuum Cleaning.
Troubleshooting for Electric Power Nozzle – Problem – electric power nozzle does not power up (motor does not turn on in power nozzle). Solution – Please follow all the steps below and try again: a. b. c. d. e. f. g. h. Unplug cord from power nozzle on hose, count 20 seconds and plug back in. Make sure the brush roll can roll freely and nothing is obstructing it. Make sure hose is firmly “snapped” into canister. Make sure main electrical wand is firmly “snapped” all the way to the hose.
