Education Services Guide Océ Reference 1.1.1.
FSC5016N_QG.fm 0 ページ ２００３年３月２４日 月曜日 午後１時４７分 Notice NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION OF THE PRODUCT. SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER’S NATIVE MODE OR ONE OF ITS EMULATION MODES. The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.
FSC5016N_QG.
FSC5016N_QG.fm 2 ページ ２００３年３月２４日 月曜日 午後１時４７分 Contents Guide to the information about the printer .................................3 Understanding the Error Messages ...........................................4 Loading Paper .........................................................................14 Clearing Paper Jams ...............................................................22 Jam at the Paper Cassette .........................................23 Jam at the Paper Transfer Unit .....................
FSC5016N_QG.fm 3 ページ ２００３年３月２４日 月曜日 午後１時４７分 Guide to the information about the printer The following documentation and CD-ROM are supplied: Installation Guide This guide provides information on installing the printer before starting to use. Quick Reference This guide provides common information Guide (This booklet) about the printer such as loading paper, understanding messages, etc. Operation Guide This guide is supplied as an online manual (PDF) in the CD-ROM.
FSC5016N_QG.fm 4 ページ ２００３年３月２４日 月曜日 午後１時４７分 Understanding the Error Messages These messages appear on the printer’s message display when the printer needs the operator’s attention. For more details, refer to chapter 4 of the Operation Guide. Message Corrective Action Add paper MPTray The paper has run out in the paper source displayed. Supply paper according to the paper source (paper cassettes, MP tray, optional paper feeders, or optional envelope feeder).
FSC5016N_QG.fm 5 ページ ２００３年３月２４日 Message Check waste toner box 月曜日 午後１時４７分 Corrective Action This message warns following two cases. Install the new waste toner box. • The waste toner box is not installed. • The waste toner box is almost full. Clean printer Press GO Please clean the inside of the printer. See Cleaning the Printer on page 35. This message will be displayed when replacing the toner container after the message Replace toner C, M, Y, K is displayed.
FSC5016N_QG.fm 6 ページ ２００３年３月２４日 Message 月曜日 午後１時４７分 Corrective Action Close top cover The top cover of the printer is open. Close the printer top cover. Duplex disabled Press GO You attempted to print with a paper size and paper type that cannot be used for duplex printing. Press the GO key to print onto one-side of the paper only. Face-down tray paper full The face-down tray has become full (approx. 250 pages). You must remove all printed pages from the face-down tray.
FSC5016N_QG.fm 7 ページ ２００３年３月２４日 Message 月曜日 午後１時４７分 Corrective Action Hard disk err ## Press GO A hard disk error has occurred. Look at the error code given in place of ## and refer to chapter 4 of the Operation Guide. To ignore the hard disk error, press the GO key. I/F occupied This message is displayed when you attempt to use the printer’s operator panel to change the environmental settings on the interface from which data are presently being received.
FSC5016N_QG.fm 8 ページ ２００３年３月２４日 Message KPDL error ## Press GO 月曜日 午後１時４７分 Corrective Action Current print processing cannot continue because of occurrence of KPDL error which is categorized by ##. To print out an error report, display > Print KPDL err(s) from the menu system, and select On. Press the GO key to resume printing. You can abandon printing by the CANCEL key. If Auto Continue is set to On, printing will be automatically resumed after a preset period of time.
FSC5016N_QG.fm 9 ページ ２００３年３月２４日 Message Load EF (A5)/(PLAIN)† 月曜日 午後１時４７分 Corrective Action There is no paper cassette installed in the printer that matches the paper size and paper type of the print job. Set paper in the envelope feeder. Press the GO key to resume printing. (Note that feeding the paper having a paper size which does not match the current paper size from the envelope feeder can cause paper jam.
FSC5016N_QG.fm 10 ページ Message Load MP Tray (A4)/(PLAIN)† ２００３年３月２４日 月曜日 午後１時４７分 Corrective Action There is no paper cassette installed in the printer that matches the paper size and paper type of the print job. Set paper in the MP tray. Press the GO key to resume printing. (Note that feeding the paper having a paper size which does not match the current paper size from the MP tray can cause paper jam.
FSC5016N_QG.fm 11 ページ ２００３年３月２４日 Message Memory overflow Press GO 月曜日 午後１時４７分 Corrective Action The total amount of data received by the printer exceeds the printer’s internal memory. Try adding more memory. Press the GO key to resume printing. You can abandon printing by the CANCEL key. If Auto Continue is set to On, printing will be automatically resumed after a preset period of time. For details on Auto Continue, refer to chapter 3 of the Operation Guide.
FSC5016N_QG.fm 12 ページ ２００３年３月２４日 Message Print overrun Press GO†† 月曜日 午後１時４７分 Corrective Action The print job transferred to the printer was too complex to print on a page. Press the GO key to resume printing. (The page may break in some pages.). You can abandon printing by the CANCEL key. If Auto Continue is set to On, printing will be automatically resumed after a preset period of time. For details on Auto Continue, refer to chapter 3 of the Operation Guide.
FSC5016N_QG.fm 13 ページ ２００３年３月２４日 Message 月曜日 午後１時４７分 Corrective Action Virtual mailbox full The storage area in the hard disk for the virtual mailboxes is full. Print out accumulated jobs in the virtual mailboxes. Warning low memory The printer’s internal memory is running low due to too many numbers of fonts and macros downloaded. Try deleting unnecessary fonts and macros. † †† Messages separated by ‘( )/( )’ are displayed alternately.
FSC5016N_QG.fm 14 ページ ２００３年３月２４日 月曜日 午後１時４７分 Loading Paper Caution Fan the media (paper/transparencies), then tap it on a level surface to avoid media jams or skewed printing. 1 Loading paper into the cassette Pull the paper cassette all the way out of the printer.
FSC5016N_QG.fm 15 ページ ２００３年３月２４日 月曜日 午後１時４７分 2 Push the bottom plate down until it locks. Bottom Plate Standard paper sizes are attached to the inside of the paper cassette as shown in the following figure.
FSC5016N_QG.fm 16 ページ ２００３年３月２４日 月曜日 3 Paper Size Dial Note Turn the paper size dial so that the size of the paper you are going to use appears in the paper size window. Paper Size Window When the paper size dial is set to OTHER the paper size must be set into the printer on the operator panel. See chapter 3 of the Operation Guide. 4 Release Lever 16 午後１時４７分 Paper Guides Adjust the position of the paper guides located on the left and right sides of the paper cassette.
FSC5016N_QG.fm 17 ページ ２００３年３月２４日 月曜日 午後１時４７分 5 Release Lever Paper Stopper Adjust the position of the paper stopper located at the rear of the paper cassette. Pull the release lever and slide the paper stopper to the desired paper size. When shipped from the factory, the paper cassette is set to A4 size. A4 B5 When using non-standard size paper, move the paper guides and paper stopper all the way out, insert the paper, then adjust the paper guides and paper stopper to the size of the paper.
FSC5016N_QG.fm Note 18 ページ ２００３年３月２４日 月曜日 • Do not load more paper than will fit under the load limits on the paper guides. • The paper cassette will hold approximately 500 sheets of paper with a 80 g/m² (21 lb.) basis weight, or with a thickness of 0.11 mm. Load Limit Load Limit 7 Clip 18 午後１時４７分 Clip Set the stack of paper so that it is under the clips as shown.
FSC5016N_QG.fm 19 ページ ２００３年３月２４日 月曜日 午後１時４７分 8 Insert the paper cassette into the slot in the printer. Push it straight in as far as it will go. There is a paper gauge on the right side of the front of the paper cassette to indicate the remaining paper supply. When paper is exhausted, the pointer will go down to the level of (empty).
FSC5016N_QG.fm 20 ページ ２００３年３月２４日 月曜日 1 MP Tray 午後１時４７分 Loading paper into the MP (Multi-Purpose) tray Pull the MP tray towards you until it stops. 2 Pull out the subtray. Subtray A4 LTR 3 B5 A5 Paper Guides 20 Adjust the position of the paper guides on the MP tray. Standard paper sizes are attached to the MP tray. For standard paper sizes, slide the guides to the position marked correspondingly.
FSC5016N_QG.fm 21 ページ ２００３年３月２４日 月曜日 午後１時４７分 4 Load Limit Note Align the paper with the paper guides and insert as far as it will go. Load Limit • Do not load more paper than will fit under the load limits on the inside of the MP tray. • If the paper is considerably curled in one direction, for example, if the paper is already printed on one side, try to roll the paper in the opposite direction to counteract the curl. Printed sheets will then come out flat.
FSC5016N_QG.fm 22 ページ ２００３年３月２４日 月曜日 午後１時４７分 Clearing Paper Jams The figure below is a simplified diagram showing the paper paths in the print system. You can clear paper jams easily and quickly if you become familiar with the paper paths and locations of potential jams. Duplex unit DU-300 Paper Feeder PF-60 Depending on the indication on the message display, proceed as follows: Caution 22 When pulling the paper, pull it gently so as not to tear it.
FSC5016N_QG.fm 23 ページ ２００３年３月２４日 月曜日 午後１時４７分 Jam at the Paper Cassette Pull out the paper cassette and remove the jammed paper. If paper is jammed at the standard paper cassette (Cassette 1), open and close the paper transfer unit (the paper jam error will be reset). Jam at the Paper Transfer Unit 1 While pulling the green paper transfer unit release lever, pull out the paper transfer unit.
FSC5016N_QG.fm A 24 ページ ２００３年３月２４日 月曜日 2 午後１時４７分 If paper is jammed as shown in A, remove the paper by pulling the center up. Registration Roller If paper is jammed as shown in B, remove the paper by pulling the edge.
FSC5016N_QG.fm 25 ページ ２００３年３月２４日 月曜日 午後１時４７分 Jam at the Rear Cover 1 While pulling the green paper transfer unit release lever, pull out the paper transfer unit. Paper Transfer Unit Release Lever Paper Transfer Unit 2 Open the rear cover and then the fuser cover, and remove the jammed paper.
FSC5016N_QG.fm Caution 26 ページ ２００３年３月２４日 月曜日 午後１時４７分 The fuser unit inside the printer is hot. Do not touch it with your hands as it may result in burn injury. Remove jammed paper carefully. Push the paper transfer unit back in and close the fuser cover and rear cover. Jam at the MP Tray Remove the paper jammed at the MP tray. Open and close the paper transfer unit (the paper jam error will be reset).
FSC5016N_QG.fm 27 ページ ２００３年３月２４日 月曜日 午後１時４７分 Toner Container Replacement The life of the toner containers depends on the amount of toner required to accomplish your printing jobs.
FSC5016N_QG.fm 28 ページ ２００３年３月２４日 月曜日 午後１時４７分 Replacing the Toner Container Note You do not have to turn printer power off before starting the replacement. Any data that may be under printing process will be deleted if you turn printer power off. To replace the toner container, first make sure of the color of the toner container requiring replacement according to the message display. In this example, it is assumed that you are replacing the black toner container. 1 Open the top cover.
FSC5016N_QG.fm 29 ページ ２００３年３月２４日 月曜日 午後１時４７分 3 Carefully remove the old toner container from the printer. 4 Put the old toner container in the plastic bag (contained in the toner kit) and discard it later according to the local code or regulations for waste disposal. 5 Take the new toner container out of the toner kit. Shake the new toner container 5 or 6 times as shown in the figure in order to distribute the toner evenly inside the container.
FSC5016N_QG.fm 30 ページ ２００３年３月２４日 月曜日 Lock Lever 30 午後１時４７分 6 Set the new toner container in the printer as shown in the figure. 7 Push down on the top of the toner container to install it firmly in place. 8 Push the blue lock lever on the toner container back towards the locked symbol ( ) as far as it will go.
FSC5016N_QG.fm 31 ページ ２００３年３月２４日 月曜日 午後１時４７分 To replace the other color toner containers, use the same procedure above. 9 Close the top cover. When the toner container has been replaced, proceed to the next section.
FSC5016N_QG.fm 32 ページ ２００３年３月２４日 月曜日 午後１時４７分 Replacing the Waste Toner Box Replace the waste toner box each time you replace the toner container. A new waste toner box is included with the toner kit. The printer will not operate without replacing the waste toner box. Left Cover 1 Open the left cover. 2 While holding the waste toner box, press the lock lever and then gently remove the waste toner box.
FSC5016N_QG.fm 33 ページ ２００３年３月２４日 月曜日 午後１時４７分 3 Cap Close the cap to the old waste toner box after removing the box from the printer. Old Waste Toner Box 4 To prevent toner from spilling, put the old waste toner box in the plastic bag (contained in the toner kit) and discard it later according to the local code or regulations for waste disposal. 5 Open the cap of the new waste toner box.
FSC5016N_QG.fm 34 ページ ２００３年３月２４日 月曜日 午後１時４７分 6 Insert the new waste toner box as shown in the figure. When the box is set correctly, it will snap into place. 7 Make sure that the waste toner box is correctly inserted and close the left cover. New Waste Toner Box The printer parts must be cleaned when replacing the toner container. See Cleaning the Printer on page 35. When the toner container is replaced, reset the toner counter (see chapter 3 of the Operation Guide).
FSC5016N_QG.fm 35 ページ ２００３年３月２４日 月曜日 午後１時４７分 Cleaning the Printer The following parts must be cleaned each time the toner container is replaced: • • • Main charger wire Main charger grid Registration roller In addition to this, it is recommended that the main charger wire and registration roller are cleaned periodically at least once a month. Cleaning the Main Charger Unit The main charger units need to be cleaned periodically as they get contaminated with dioxide after long usage.
FSC5016N_QG.fm 36 ページ ２００３年３月２４日 月曜日 午後１時４７分 There are 4 main charger units, one for each toner container. When performing the cleaning procedure, be sure to clean the main charger unit that corresponds to the toner container that was replaced. The following example explains the procedure to clean the main charger unit for the black toner container. Main Charger Units MC Y K Left Cover 36 1 Open the left cover.
FSC5016N_QG.fm 37 ページ ２００３年３月２４日 月曜日 午後１時４７分 2 Cleaning the main charger wire — Grasp the tab of the green wire cleaner knob. Gently pull the wire cleaner out and push it back in. Repeat this 2 to 3 times. Wire Cleaner Knob After cleaning, make sure you restore the wire cleaner knob to its home position. Note If the wire cleaner knob is not restored to its home position, a band will print along the length of the page.
FSC5016N_QG.fm 38 ページ ２００３年３月２４日 月曜日 午後１時４７分 The pad of the grid cleaner contains water. Clean the grid quickly so that the pad may not dry off. Note Grid Cleaner 38 4 Lift up slightly on the main charger unit and pull it out a short distance as shown in the figure. 5 Attach the grid cleaner to the printer with the pad facing up.
FSC5016N_QG.fm 39 ページ ２００３年３月２４日 月曜日 午後１時４７分 6 Gently pull the main charger handle out and push it back in. Repeat this 2 to 3 times. These movements clean the grid. Main Charger Unit After cleaning, make sure you restore the main charger unit to its home position. Note If the main charger unit is not restored to its home position, the corresponding color will be printed over the whole page. 7 After cleaning is finished, remove the grid cleaner from the printer and discard it.
FSC5016N_QG.fm 40 ページ ２００３年３月２４日 月曜日 8 午後１時４７分 Close the left cover. Cleaning the Paper Transfer Unit Print problems such as soiling of the reverse side of printed pages may occur if the paper transfer unit becomes dirty. To clean the paper transfer unit: Note Be careful not to touch the black transfer roller during cleaning as this may adversely affect print quality.
FSC5016N_QG.fm 41 ページ Paper Ramp ２００３年３月２４日 月曜日 午後１時４７分 2 Wiper Cloth Paper Transfer Unit Wipe away the paper dust on the registration roller and the paper ramp using the wiper cloth included in the toner kit. Transfer Roller (Black) Registration Roller (Metal) Push the paper transfer unit back in.
Kyocera Mita Corporation 2-28, 1-Chome, Tamatsukuri, Chuo-ku Osaka 540-8585, Japan Phone: (06) 6764-3555 FS-C5016N Color Page Printer FS-C5016N © 2003 by KYOCERA MITA CORPORATION All rights reserved. 2003.
