INSTRUCTION www.oakworks.com · 717.235.
© Copyright 2009 Oakworks® , Inc. Notice The information contained in this document is subject to change without notice and should not be construed as a commitment by Oakworks®, Inc. Printed in U.S.A. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Oakworks®, Inc. Oakworks® is a registered trademark of Oakworks®, Inc. Oakworks®, Inc.
TABLE OF CONTENTS Symbol Identification .................................................................................... pg 2 Warnings & Safety Instructions ..................................................................... pg 3 Grounding Instructions .................................................................................. pg 5 Product Description & Table Specs ............................................................. pg 6 Assembly & Installation ...............................
SYMBOL IDENTIFICATION SYMBOL IDENTIFICATION WARNINGS SYMBOL IDENTIFICATION This symbol, when used in this manual and on product labels, represents a caution. Be sure to read and comply with all precautions and warnings. This symbol, when used in documentation on this product, indicates danger and warns against an electrical shock hazard. Be sure to observe and comply with all warnings and instructions. This symbol, when used in documentation on this product, indicates a Protective Earth (Ground) Terminal.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS WARNINGS & CAUTIONS Improper use of this device can cause injury. Be sure to read all operating instructions prior to use to prevent injury to operator or client. WARNING Electrical Shock Hazard. To reduce the risk of electric shock, always disconnect the table from the electrical outlet before moving the table or doing any maintenance or troubleshooting procedures. Never use this equipment if it has a damaged cord or plug.
WARNINGS & SAFETY INSTRUCTIONS WARNINGS WARNINGS / SAFETY WARNINGS & SAFETY INSTRUCTIONS WARNING Close supervision is necessary when this furnishing is used by, or near, children, invalids or disabled persons. DO NOT leave children alone or allow them to operate the controls. Keep controls out of reach of children. DO NOT allow children to crawl under the table. CAUTION Be certain that the table is completely lowered prior to discharging an ambulatory patient. The patient may lose balance and fall.
GROUNDING INSTRUCTIONS IMPORTANT CAUTION READ AND SAVE THESE INSTRUCTIONS GROUNDING GROUNDING INSTRUCTIONS (ELECTRIC MODEL ONLY) This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.
PRODUCT DESCRIPTION PRODUCT DESCRIPTION PRODUCT DESCRIPTION Flat top Shown with additional accessories; QuickLock™ Face Rest with Boiance™ Crescent Maple base with custom inlay stripe Butcher block leg design Foot Control Spring leg design with Backrest Top TABLE SPECIFICATIONS • Height Range: 24” - 34” (61-86 cm) • Width: 29” or 31” (74 cm or 79 cm) • Length: 73” (185 cm) • Lift Capacity: 400 lbs. (182 kg.) • Weight: 200 lbs. (91 kg.) • Shipping Weight: 250 lbs. (114 kg.
INSTALLATION ASSEMBLY & INSTALLATION PARTS INCLUDED: INSTALLATION INSTALLATION 1 - Table 4 - Main Legs 1 - Wrench (depending on style specified) 8 - Washers 8 - Nylock Nuts step 1 step 2 step 3 Locate the pack of legs & hardware and set aside. Finish removing all packing material, leaving the corner blocks in place. Place the leg bolt through the metal corner bracket in one corner of the table skirt. step 4 step 5 step 6 Place a flat washer and nut on each bolt.
INSTALLATION INSTALLATION INSTALLATION Plug the cord into a functioning outlet that is rated for the table. (Electric models only) Arrange the power cord and foot switch (electric model only) so that they will not create a tripping hazard. Place the controls in a safe location where they are convenient and accessible. Keep the controls out of the way of all table mechanisms.
DIRECTIONS FOR USE DIRECTIONS FOR USE ADJUSTING HEIGHT OF THE TABLE The Oakworks® Virgo™ comes complete with a foot control or manual hand crank that operates the height with ease. Height Control - Electric Model Operate the foot control as shown below to raise or lower the height of the table. When operating the table’s controls, be sure to observe all cautions and warnings as given in the manual.
DIRECTIONS FOR USE DIRECTIONS FOR USE QUICKLOCK™ FACE REST & HEAD REST QUICKLOCK™ FACE REST: Be sure to read all cautions, warnings and instructions given in the manual to prevent injury to both operator and client. Be sure to use either the face rest or head rest for all treatments that require your client to lay flat. Double articulating action provides nearly limitless positioning options with the QuickLock™ Face Rest.
DIRECTIONS FOR USE DIRECTIONS FOR USE MOVING THE VIRGO™ CAUTION The table weighs as much as 200 lbs. DO NOT lift or move the unit without using proper safety procedures or equipment. DO NOT turn the table on its side for any reason. To do so could cause damage to the base and will void the warranty. There are no serviceable items that require this action. Never lift the table by grasping the table top as the table top is not designed to hold the weight of the base and you could damage the table.
CARE & CLEANING CARE & CLEANING UPHOLSTERY CLEAN your upholstered items when needed using a mild solution of 4:1 diluted non-alcohol cleaner such as Formula 409 ®, Fantastik®, or Green Windex® Be sure to read all cautions, warnings and instructions given in the manual to prevent injury to both operator and client. DISINFECT your fabric with Protex, MadaCide, MadaWipe, Accell TB, Virox® (Canada), or a diluted 1/10 bleach solution. Dry immediately after cleaning to remove excess cleaning solution.
PART IDENTIFICATION PART IDENTIFICATION POWER LEAD PLUGS POWER LEAD PLUGS IMPORTANT Oakwork Part #: Voltage (AC) Power Cord Plug 120v 60 Hz 3 prong grounded these parts are for 7791 identification only; North America they are not field serviceable items.
SPECIFICATIONS SPECIFICATIONS ELECTRICAL SPECIFICATIONS Designed For: North America Europe Japan/Korea Voltage/Current Service 120 VAC/20 amps 220 VAC/10 amps 100 VAC/20 amps Current Draw 4.1 Amps 2.1 Amps 4.
WARRANTY WARRANTY WARRANTY For full warranty details, please visit www.oakworks.com All warranties are limited to factory-provided replacement parts, factory repair or replacement, at the discretion of Oakworks®. All warranties exclude damage caused by improper set-up, accident, abuse, misuse, neglect, use for other than intended purpose or reasonable wear such as tears in the upholstery.
THIS PAGE INTENTIONALLY LEFT BLANK 16
THIS PAGE INTENTIONALLY LEFT BLANK 17
Virgo ™ INSTRUCTION MANUAL CONTACT INFORMATION: Oakworks® Inc. 923 East Wellspring Road New Freedom, PA 17349 Phone: 717-235-6807 FAX: 717-235-6798 www.oakworks.com Manual Part Number MMMNST0014 Revision date: 12.07.
