ENHANCED OXYGEN SPRAY BOTTLE USER MANUAL Model: SB-100HD clean with the power of nature
CONTENTS 1 Safety ............................................................................................... 3 1.1 1.2 1.3 1.4 Symbols from the User Manual ...................................... 3 Proper Use.............................................................................. 3 Caution .................................................................................... 3 Important Instructions....................................................... 4 2 Technical Data .......................
SAFETY IMPORTANT! Before initial use, the instructions on operating safety, use and maintenance must be read carefully and understood. Keep the user manual in the vicinity of the appliance for later reference. 1.1 SYMBOLS FROM THE USER MANUAL CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. NOTICE NOTICE indicates a situation which, if not avoided, may result in damage to the appliance. Important information can be found here.
SAFETY (cont’d) 1.4 IMPORTANT INSTRUCTIONS NOTICE To avoid appliance damage: Do not drop the bottle. – Dropping the bottle may cause breakage. Fill with clean potable water only. – Filling the bottle with fluids other than clean potable water may damabe cartridge and render the product useless. Do not overfill the bottle. – Overfilling may cause leakage at the fill plug. Do not run water into the charger port. – Doing so may short the battery/electronics.
TECHNICAL DATA SPECIFICATIONS Materials PC/ABS Impact Resistant Plastic Weight (empty) ~ 1.45 lb (0.66 kg) Dimensions (in mm) 4.75 in x 5.5 in x 10 in (120.7 mm x 139.7 mm x 250 mm) Reservoir Capacity 10 oz (295.7 ml) Water Temperature 40°F to 86°F (4°C to 30°C) Water Quality Hardness ≤ 250 ppm CACO3 (May Extend Life of Unit) Conductivity >50 μS/cm (Cell damage may result from use of distilled or deionized water) Ambient Air 40°F to 104°F (4°C to 40°C) Rechargable Battery 7.
DESCRIPTION 3.1 DESCRIPTION The O3waterworks Enhanced Oxygen Spray Bottle offers a water-based alternative to tradtional cleaners and sanitizers. It turns potable water into aqueous ozone, a sanitizer that kills many common pathogens found on hard, non-porous surfaces and destroys organic odors. The tiny electrolytic cell is created from a proprietary diamond process technology and generates ozone on-demand from water itself.
Water Based Sanitizer • Proven sanitizer • Reduces common pathogens • Destroys odor-causing microorganisms • Ensures efficacy and compliance with EPA requirements Dependable, On-Demand Solution • Ozone (O3) is activated as-needed • Runs on long lasting rechargeable batteries • Requires only clean, potable water • User-friendly lights indicate when sanitizer is active Alternative • Leaves behind no residues • Compatible with all surfaces where water may be used • Eliminates potential errors with mixing or di
Fill the Reservoir Prepare 10 oz of clean, cold potable water to fill the bottle. Remove the fill plug and tilt the bottle at a 45° angle. Fill the reservoir with 10 oz of clean, cold potable water. Replace the fill plug securely. Return bottle to vertical position and check fill line. Adjust until water reaches fill line. Do not overfill. Do not fill with hot water or any cleaning products. Remove cap. CAUTION FILL WITH CLEAN, COLD POTABLE WATER ONLY. DO NOT OVERFILL THE BOTTLE.
Sanitize Hard Non-Porous Surface Hold the spray bottle 6 to 8 inches from the surface and spray evenly until wet. For 99.9% effectiveness against common pathogens allow to stand for 30 seconds. Wipe with a clean cotton or microfiber cloth or allow to air dry. No rinsing is necessary (leaves no residue). Ozone is generated on demand. While spraying, the blue indicator will light when the unit is operating properly. PREV ENTATIVE MAINTENANCE & CLEANING 1.
DECOMMISSIONING ( STORAGE / DISPOSAL ) 6.1 STORAGE Empty tank through the fill plug. Do not spray empty. Leave fill plug open to allow tank to dry. 6.2 DISPOSAL Disassembly of the appliance must be performed by qualified specialists according to the manufacturer’s instructions. – Follow the local safety regulations. – Dispose of the appliance in accordance with local regulations. – It is essential that you observe the laws and regulations for the disposal of environmentally harmful substances.
SERVICE 7.1 SERVICE & WARRANTY The manufacturer warrants new equipment to be free of defects due to poor materials or workmanship for the period of time listed below (following the date of original installation): • One year replacement Exclusions: Certain O3waterworks parts that are expendable by nature and that need to be replaced frequently may not be covered.
Distributed by: o3waterworks, LLC. 207 Byers Creek Road, Unit D Mooresville, NC 28117 Manufactured by: Enozo Technologies 300 Willow Street North Andover, MA 01845 EPA Est. No. 089373-MA-001 For support, contact: support@o3waterworks.