Datasheet

MC33411A/B
7
MOTOROLA RF/IF DEVICE DATA
ELECTRICAL CHARACTERISTICS (continued) (V
CC
= 3.6 V, V
B
= 1.5 V, T
A
= 25°C, Active Mode, Rx Gain = 01111,
Vol Adj = 0111, f
in
= 1.0 kHz, unless otherwise noted.)
Characteristics UnitMaxTypMinSymbol
Measure
Pin
Input
Pin
MICROPROCESSOR INTERFACE (V
CC
= 3.6 V, V
B
= 1.5 V, T
A
= 25°C, Active or Receive Mode)
Output Low Voltage (I
ol
= 0 mA) MCU Clk
Out
V
ol
– 0.1 0.3 V
Output High Voltage (I
oh
= 0 mA) Data V
oh
Tx PLL
V
CC
–
0.3
3.5 – V
Output Low Voltage (I
ol
= 0 mA) Data V
ol
– 0.1 0.3 V
Rx/Tx PLL CHARACTERISTICS (V
CC
= 3.6 V, V
B
= 1.5 V, T
A
= 25°C, Active or Receive Mode)
Output Source Current (V
PD
= 0.5 V or
V
CC
– 0.5 V)
I
oh
µA
±100 µA mode Rx PD & –130 –100 –70
±400 µA mode Tx PD –520 –400 –280
Output Sink Current (V
PD
= 0.5 V or V
CC
– 0.5 V) I
ol
µA
±100 µA mode Rx PD & 70 100 130
±400 µA mode Tx PD 280 400 520
Current Match, ±100 µA mode or ±400 µA mode,
V
PD
= V
CC
/ 2 (i.e., 100 x (ABS (I
oh
/ I
ol
)))
Rx PD
Tx PD
Match 80 100 125 %
Output Off Current (V
PD
= V
CC
/2),±100 µA mode
or ±400 µA mode
Rx PD
Tx PD
I
oz
–80 5.0 80 nA
Input Current Low (V
in
= 0 V) FRx FTx I
il
–10 –7.5 – µA
Input Current High (V
in
= V
CC
) FRx FTx I
ih
– 10 14 µA
Input Bias Voltage FRx FTx V
bias
– 1.5 – V
Output Voltage High (I
oh
= 0 mA, Voltage Mode) FRxMC V
oh
– Rx PLL
V
CC
– 0.1
– V
Output Voltage High (I
oh
= 0 mA, Voltage Mode) FTxMC V
oh
– Tx PLL
V
CC
– 0.1
– V
Output Voltage Low (I
ol
= 0 mA, Voltage Mode) FRxMC
FTxMC
V
ol
– 0.1 – V
Output Current High (V
oh
= 0.8 V, Current Mode) FRxMC
FTxMC
I
oh
–130 –100 –70 µA
Output Current Low (V
ol
= 0.8 V, Current Mode) FRxMC
FTxMC
I
ol
70 100 130 µA
Maximum Input Frequency FRx
FTx
F
max
20 – – MHz
Input Voltage Swing FRx
FTx
V
in
200 – 1200 mVpp
Modulus Control Prop Delay FRx
FTx
FRxMC
FTxMC
– – 20 – nS
LO2 PLL CHARACTERISTICS (V
CC
= 3.6 V, V
B
= 1.5 V, T
A
= 25°C, Active Mode)
Output Source Current (V
PD
= 0.5 V or
V
CC
– 0.5 V)
LO2PD I
oh
µA
±100 µA mode –130 –100 –70
±400 µA mode –520 –400 –280
Output Sink Current (V
PD
= 0.5 V or V
CC
– 0.5 V) LO2PD I
ol
µA
±100 µA mode 70 100 130
±400 µA mode 280 400 520
Current Match, ±100 µA mode or ±400 µA mode,
V
PD
= V
CC
/ 2 (i.e., 100 x (ABS (I
oh
/ I
ol
)))
LO2PD Match 80 100 125 %
NOTES: 1. Values specified are pure numbers to the base 10.
2. Typical performance parameters indicate the potential of the device under ideal operating conditions.
ARCHIVE INFORMATION
ARCHIVE INFORMATION
Fr
eescale S
emiconduct
or
, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...