Datasheet

Analog Integrated Circuit Device Data
18 Freescale Semiconductor
10XSC425
4.3 Dynamic Electrical Characteristics
Table 5. Dynamic Electrical Characteristics
Characteristics noted under conditions 6.0 V V
PWR
 20 V, 3.0 V  V
DD
 5.5 V, - 40 C  T
A
 125 C, GND = 0 V, unless
otherwise noted. Typical values noted reflect the approximate parameter means at T
A
= 25 °C under nominal conditions, unless
otherwise noted.
Symbol Characteristic Min Typ Max Unit Notes
POWER OUTPUT TIMING HS0 TO HS3
SR
R00
Output Rising Medium Slew Rate (medium speed slew rate / SR[1:0] = 00)
300 650 1200
mV/s
SR
F00
Output Falling Medium Slew Rate (medium speed slew rate / SR[1:0] = 00)
300 720 1200
mV/s
DS
R_00
Driver Output Matching Slew Rate (SRR /SRF)
•PWR = 14 V at 25 °C and for medium speed slew rate 
(SR[1:0] = 00) V
0.8 0.9 1.2
SR
R01
Output Rising Low Slew Rate (medium speed slew rate / SR[1:0] = 01)
150 330 600
mV/s
SR
F01
Output Falling Low Slew Rate (medium speed slew rate / SR[1:0] = 01)
150 370 600
mV/s
SR
R10
Output Rising Fast Slew Rate (medium speed slew rate / SR[1:0] = 10)
600 1250 2400
mV/s
SR
F10
Output Falling Fast Slew Rate (medium speed slew rate / SR[1:0] = 10)
600 1450 2400
mV/s
t
DLY_ON
HS[0:1] Outputs Turn-ON Delay Times
• VPWR = 14 for medium speed slew rate (SR[1:0] = 00) V
40 64 100
s
(28),(29)
t
DLY_OFF
HS[0:1] Outputs Turn-OFF Delay Times
• VPWR = 14 for medium speed slew rate (SR[1:0] = 00) V
10 32 60
s
(28),(29)
t
RF
HS[0:1] Driver Output Matching Time (t
DLY(ON)
- t
DLY(OFF)
)
• VPWR = 14 V, f
PWM
= 240 Hz, PWM duty cycle = 50%, at 25 °C for
medium speed slew rate (SR[1:0] = 00)
10 32 60
s
(28),(29)
SR
R00
HS[2,3] Output Overcurrent Detection Levels (6.0 V < V
HS[0:3]
< 20 V)
200 470 800
mV/s
SR
F00
HS[2,3] Output Overcurrent Detection Levels (6.0 V < V
HS[0:3]
< 20 V)
200 570 800
mV/s
DS
R_00
HS[2,3] Output Overcurrent Detection Levels (6.0 V < V
HS[0:3]
< 20 V)
0.6 0.8 1.0
SR
R01
HS[2,3] Output Overcurrent Detection Levels (6.0 V < V
HS[0:3]
< 20 V)
100 230 400
mV/s
SR
F01
HS[2,3] Output Overcurrent Detection Levels (6.0 V < V
HS[0:3]
< 20 V)
100 300 400
mV/s
Notes
28. Turn ON delay time measured from rising edge of any signal (IN[0 : 3] and CSB) that would turn the output ON to V
HS[0 : 3]
= V
PWR
/ 2 with
R
L
= 5.0  resistive load.
29. Turn OFF delay time measured from falling edge of any signal (IN[0 : 3] and CSB) that would turn the output OFF to V
HS[0 : 3]
= V
PWR
/ 2
with R
L
= 5.0  resistive load.