Datasheet

ManualsBrandsNXP SEMICONDUCTORS ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller MAPBGA 473 (19x19) MPC83xx 32-Bit Single-Core 333 MHz

MPC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 3

70 Freescale Semiconductor

Package and Pin Listings

Y23, H8, H9, H10, H14, H15, H16, J8, J16, K8, K16, L8, L16, M8,

M16, N8, N16, P8, P16, R8, R16, T8, T9, T10, T11, T12, T13, T14,

T15, T16

I——

VSS A2, A21, B1, B19, B23, C4, C16, D6, D19, E3, F8, F15, F17, F23,

G7, G8, G10, G15, G16, G17, G20, H2, H6, H7, H17, H23, J7, J9,

J10, J11, J12, J13, J14, J15, K9, K10, K11, K12, K13, K14, K15,

L1, L7, L9, L10, L11, L12, L13, L14, L15, L20, M4, M9, M10, M11,

M12, M13, M14, M15, N9, N10, N11, N12, N13, N14, N15, P6, P7,

P9, P10, P11, P12, P13, P14, P15, R2, R7, R9, R10, R11, R12,

R13, R14, R15, R22, T6, T7, U8, U17, U21, V2, V7, V9, V11, W20,

Y8, Y15, AA4, AB1, AB6, AB12, AB19, AC2, AC9, AC23

I — —

DDA

B7, B10, C7, D9, F9 I — —

DDB

A16, A19, C18 I — —

DDC

A23, B22, D23, E20, G18 I — —

DDF

G22, J22, K17 I — —

DDG

M17, N22 I — —

DDH

P17, R20, T17, T23, W22, Y22 I — —

DDJ

AB23, AA22 I — —

DDP_K

U10, U14, Y5, Y18, AA11, AB8, AB16, AB22, AC4,

AC13

I — —

A1, A6, B3, D1, F1, F6, G4, J1, J4, K7, N1, N7, T1, T4, U7, Y3, AC1 I — —

XPADVDD D15, F10, F14 I — —

XPADVSS A10, B15, D14, G13, G14, H12 I — —

XCOREVDD A14, B12, C13 I — —

XCOREVSS A12, B14, C11, D11, D13, G11, H11, H13 I — —

Notes:

1. This pin is an open drain signal. A weak pull-up resistor (1 k) should be placed on this pin to NV

2. This pin is an open drain signal. A weak pull-up resistor (2–10 k) should be placed on this pin to NV

3. This output is actively driven during reset rather than being three-stated during reset.

4. This pin has weak internal pull-up that is always enabled. 5. This pin must always be tied to VSS.

6. Internal thermally sensitive resistor, resistor value varies linearly with temperature. Useful for determining the junction

temperature.

7. The LB_POR_CFG_BOOT_ECC is sampled only during the PORESET

negation. This pin with an internal pull down resistor

enables the ECC by default. To disable the ECC an external strong pull up resistor or a buffer released to high impedance is

needed.

8. This pin has weak internal pull-down that is always enabled

Table 53. MPC8308 Pinout Listing (continued)

Signal Package Pin Number

Type

Power

Supply

Note