Datasheet

ManualsBrandsNXP SEMICONDUCTORS ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller QFP 64 (14x14) 8-Bit 8 MHz I/O number 51

241

242

243

244

245

246

247

248

249

250

Table Of Contents

List of Sections
Table of Contents
List of Figures
List of Tables
Section 1. General Description
- 1.1 Contents
- 1.2 Introduction
- 1.3 Features
- 1.4 MCU Block Diagram
- 1.5 Pin Assignments
- 1.6 Pin Functions
- 1.7 I/O Pin Summary
- 1.8 Signal Name Conventions
- 1.9 Clock Source Summary
Section 2. Memory Map
- 2.1 Contents
- 2.2 Introduction
- 2.3 Unimplemented Memory Locations
- 2.4 Reserved Memory Locations
- 2.5 Input/Output (I/O) Section
Section 3. Random-Access Memory (RAM)
- 3.1 Contents
- 3.2 Introduction
- 3.3 Functional Description
Section 4. FLASH Memory
- 4.1 Contents
- 4.2 Introduction
- 4.3 Functional Description
- 4.4 FLASH Control Register
- 4.5 FLASH Page Erase Operation
- 4.6 FLASH Mass Erase Operation
- 4.7 FLASH Program/Read Operation
- 4.8 FLASH Block Protection
  - 4.8.1 FLASH Block Protect Register
- 4.9 Wait Mode
- 4.10 Stop Mode
Section 5. EEPROM
- 5.1 Contents
- 5.2 Introduction
- 5.3 Features
- 5.4 Functional Description
- 5.5 EEPROM Configuration
- 5.6 EEPROM Timebase Requirements
- 5.7 EEPROM Security Options
- 5.8 EEPROM Block Protection
- 5.9 EEPROM Programming and Erasing
  - 5.9.1 EEPROM Programming
  - 5.9.2 EEPROM Erasing
- 5.10 Low Power Modes
  - 5.10.1 Wait Mode
  - 5.10.2 Stop Mode
- 5.11 EEPROM Registers
Section 6. Configuration Register (CONFIG)
- 6.1 Contents
- 6.2 Introduction
- 6.3 Functional description
- 6.4 Configuration Register 1
- 6.5 Configuration Register 2
Section 7. Central Processor Unit (CPU)
- 7.1 Contents
- 7.2 Introduction
- 7.3 Features
- 7.4 CPU Registers
- 7.5 Arithmetic/Logic Unit (ALU)
- 7.6 Low-Power Modes
  - 7.6.1 Wait Mode
  - 7.6.2 Stop Mode
- 7.7 CPU During Break Interrupts
- 7.8 Instruction Set Summary
- 7.9 Opcode Map
Section 8. System Integration Module (SIM)
- 8.1 Contents
- 8.2 Introduction
- 8.3 SIM Bus Clock Control and Generation
- 8.4 Reset and System Initialization
  - 8.4.1 External Pin Reset
  - 8.4.2 Active Resets from Internal Sources
- 8.5 SIM Counter
- 8.6 Exception Control
- 8.7 Low-Power Modes
  - 8.7.1 Wait Mode
  - 8.7.2 Stop Mode
- 8.8 SIM Registers
Section 9. Clock Generator Module (CGM)
- 9.1 Contents
- 9.2 Introduction
- 9.3 Features
- 9.4 Functional Description
- 9.5 I/O Signals
- 9.6 CGM Registers
- 9.7 Interrupts
- 9.8 Low-Power Modes
  - 9.8.1 Wait Mode
  - 9.8.2 Stop Mode
- 9.9 CGM During Break Interrupts
- 9.10 Acquisition/Lock Time Specifications
Section 10. Monitor ROM (MON)
- 10.1 Contents
- 10.2 Introduction
- 10.3 Features
- 10.4 Functional Description
- 10.5 Security
- 10.6 Extended Security
Section 11. Timer Interface Module A (TIMA)
- 11.1 Contents
- 11.2 Introduction
- 11.3 Features
- 11.4 Pin Name Conventions
- 11.5 Functional Description
- 11.6 Interrupts
- 11.7 Low-Power Modes
  - 11.7.1 Wait Mode
  - 11.7.2 Stop Mode
- 11.8 TIMA During Break Interrupts
- 11.9 I/O Signals
  - 11.9.1 TIMA Clock Pin
  - 11.9.2 TIMA Channel I/O Pins
- 11.10 I/O Registers
Section 12. Timer Interface Module B (TIMB)
- 12.1 Contents
- 12.2 Introduction
- 12.3 Features
- 12.4 Pin Name Conventions
- 12.5 Functional Description
- 12.6 Interrupts
- 12.7 Low-Power Modes
  - 12.7.1 Wait Mode
  - 12.7.2 Stop Mode
- 12.8 TIMB During Break Interrupts
- 12.9 I/O Signals
  - 12.9.1 TIMB Clock Pin
  - 12.9.2 TIMB Channel I/O Pins
- 12.10 I/O Registers
Section 13. Programmable Interrupt Timer (PIT)
- 13.1 Contents
- 13.2 Introduction
- 13.3 Features
- 13.4 Functional Description
  - 13.4.1 PIT Counter Prescaler
- 13.5 Low-Power Modes
  - 13.5.1 Wait Mode
  - 13.5.2 Stop Mode
- 13.6 PIT During Break Interrupts
- 13.7 I/O Registers
Section 14. Analog-to-Digital Converter (ADC)
- 14.1 Contents
- 14.2 Introduction
- 14.3 Features
- 14.4 Functional Description
- 14.5 Interrupts
- 14.6 Low-Power Modes
  - 14.6.1 Wait Mode
  - 14.6.2 Stop Mode
- 14.7 I/O Signals
- 14.8 I/O Registers
Section 15. Serial Communications Interface Module (SCI)
- 15.1 Contents
- 15.2 Introduction
- 15.3 Features
- 15.4 Pin Name Conventions
- 15.5 Functional Description
- 15.6 Low-Power Modes
  - 15.6.1 Wait Mode
  - 15.6.2 Stop Mode
- 15.7 SCI During Break Module Interrupts
- 15.8 I/O Signals
  - 15.8.1 PTE0/TxD (Transmit Data)
  - 15.8.2 PTE1/RxD (Receive Data)
- 15.9 I/O Registers
Section 16. Serial Peripheral Interface Module (SPI)
- 16.1 Contents
- 16.2 Introduction
- 16.3 Features
- 16.4 Pin Name Conventions and I/O Register Addresses
- 16.5 Functional Description
  - 16.5.1 Master Mode
  - 16.5.2 Slave Mode
- 16.6 Transmission Formats
- 16.7 Queuing Transmission Data
- 16.8 Error Conditions
  - 16.8.1 Overflow Error
  - 16.8.2 Mode Fault Error
- 16.9 Interrupts
- 16.10 Resetting the SPI
- 16.11 Low-Power Modes
  - 16.11.1 Wait Mode
  - 16.11.2 Stop Mode
- 16.12 SPI During Break Interrupts
- 16.13 I/O Signals
- 16.14 I/O Registers
Section 17. Input/Output (I/O) Ports
- 17.1 Contents
- 17.2 Introduction
- 17.3 Port A
  - 17.3.1 Port A Data Register (PTA)
  - 17.3.2 Data Direction Register A (DDRA)
- 17.4 Port B
  - 17.4.1 Port B Data Register (PTB)
  - 17.4.2 Data Direction Register B (DDRB)
- 17.5 Port C
  - 17.5.1 Port C Data Register (PTC)
  - 17.5.2 Data Direction Register C (DDRC)
- 17.6 Port D
- 17.7 Port E
  - 17.7.1 Port E Data Register (PTE)
  - 17.7.2 Data Direction Register E (DDRE)
- 17.8 Port F
- 17.9 Port G
  - 17.9.1 Port G Data Register (PTG)
  - 17.9.2 Data Direction Register G (DDRG)
- 17.10 Port H
  - 17.10.1 Port H Data Register (PTH)
  - 17.10.2 Data Direction Register H (DDRH)
Section 18. External Interrupt (IRQ)
- 18.1 Contents
- 18.2 Introduction
- 18.3 Features
- 18.4 Functional Description
  - 18.4.1 IRQ Pin
- 18.5 IRQ Status and Control Register (ISCR)
- 18.6 IRQ Module During Break Interrupts
Section 19. Keyboard Interrupt Module (KBI)
- 19.1 Contents
- 19.2 Introduction
- 19.3 Features
- 19.4 I/O Pins
- 19.5 Functional Description
- 19.6 Wait Mode
- 19.7 Stop Mode
- 19.8 Keyboard Module During Break Interrupts
Section 20. Computer Operating Properly (COP)
- 20.1 Contents
- 20.2 Introduction
- 20.3 Functional Description
- 20.4 I/O Signals
- 20.5 COP Control Register
- 20.6 Interrupts
- 20.7 Monitor Mode
- 20.8 Low-Power Modes
  - 20.8.1 Wait Mode
  - 20.8.2 Stop Mode
- 20.9 COP Module During Break Mode
Section 21. Low-Voltage Inhibit (LVI)
- 21.1 Contents
- 21.2 Introduction
- 21.3 Features
- 21.4 Functional Description
- 21.5 LVI Status Register (LVISR)
- 21.6 LVI Interrupts
- 21.7 Low-Power Modes
  - 21.7.1 Wait Mode
  - 21.7.2 Stop Mode
Section 22. Break Module (BRK)
- 22.1 Contents
- 22.2 Introduction
- 22.3 Features
- 22.4 Functional Description
- 22.5 Low-Power Modes
  - 22.5.1 Wait Mode
  - 22.5.2 Stop Mode
- 22.6 Break Module Registers
Section 23. Electrical Specifications
- 23.1 Contents
- 23.2 Introduction
- 23.3 Absolute Maximum Ratings
- 23.4 Functional Operating Range
- 23.5 Thermal Characteristics
- 23.6 5.0-V DC Electrical Characteristics
- 23.7 EEPROM and Memory Characteristics
- 23.8 5.0-V Control Timing
- 23.9 Timer Interface Module Characteristics
- 23.10 ADC Characteristics
- 23.11 SPI Characteristics
- 23.12 Clock Generation Module Characteristics
- 23.13 FLASH Memory Characteristics
Section 24. Mechanical Specifications
- 24.1 Contents
- 24.2 Introduction
- 24.3 64-Pin Plastic Quad Flat Pack (QFP)
Section 25. Ordering Information
- 25.1 Contents
- 25.2 Introduction
- 25.3 MC Order Numbers

Serial Communications Interface Module (SCI)

MC68HC908AB32 — Rev. 1.1 Technical Data

Freescale Semiconductor Serial Communications Interface Module (SCI)

247

15.5.2.1 Character Length

The transmitter can accommodate either 8-bit or 9-bit data. The state of

the M bit in SCI control register 1 (SCC1) determines character length.

When transmitting 9-bit data, bit T8 in SCI control register 3 (SCC3) is

the ninth bit (bit 8).

15.5.2.2 Character Transmission

During an SCI transmission, the transmit shift register shifts a character

out to the PTE0/TxD pin. The SCI data register (SCDR) is the write-only

buffer between the internal data bus and the transmit shift register. To

initiate an SCI transmission:

1. Enable the SCI by writing a logic 1 to the enable SCI bit (ENSCI)

in SCI control register 1 (SCC1).

2. Enable the transmitter by writing a logic 1 to the transmitter enable

bit (TE) in SCI control register 2 (SCC2).

3. Clear the SCI transmitter empty bit by first reading SCI status

4. Repeat step 3 for each subsequent transmission.

At the start of a transmission, transmitter control logic automatically

loads the transmit shift register with a preamble of logic 1s. After the

preamble shifts out, control logic transfers the SCDR data into the

transmit shift register. A logic 0 start bit automatically goes into the least

significant bit position of the transmit shift register. A logic 1 stop bit goes

into the most significant bit position.

The SCI transmitter empty bit, SCTE, in SCS1 becomes set when the

SCDR transfers a byte to the transmit shift register. The SCTE bit

indicates that the SCDR can accept new data from the internal data bus.

If the SCI transmit interrupt enable bit, SCTIE, in SCC2 is also set, the

SCTE bit generates a transmitter CPU interrupt request.

When the transmit shift register is not transmitting a character, the

PTE0/TxD pin goes to the idle condition, logic 1. If at any time software

clears the ENSCI bit in SCI control register 1 (SCC1), the transmitter and

receiver relinquish control of the port E pins.