Datasheet
Table Of Contents
- 1. General description
- 2. Features and benefits
- 3. Applications
- 4. Ordering information
- 5. Block diagram
- 6. Pinning information
- 7. Functional description
- 7.1 ARM Cortex-M0 processor
- 7.2 On-chip flash program memory
- 7.3 On-chip SRAM
- 7.4 Memory map
- 7.5 Nested Vectored Interrupt Controller (NVIC)
- 7.6 IOCONFIG block
- 7.7 Fast general purpose parallel I/O
- 7.8 UART
- 7.9 SPI serial I/O controller
- 7.10 I2C-bus serial I/O controller
- 7.11 C_CAN controller
- 7.12 10-bit ADC
- 7.13 General purpose external event counter/timers
- 7.14 System tick timer
- 7.15 Watchdog timer
- 7.16 Clocking and power control
- 7.17 System control
- 7.18 Emulation and debugging
- 8. Limiting values
- 9. Static characteristics
- 10. Dynamic characteristics
- 11. Application information
- 12. Package outline
- 13. Soldering
- 14. Abbreviations
- 15. Revision history
- 16. Legal information
- 17. Contact information
- 18. Contents

LPC11CX2_CX4 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 3.1 — 15 May 2013 48 of 62
NXP Semiconductors
LPC11Cx2/Cx4
32-bit ARM Cortex-M0 microcontroller
[1] T
cy(clk)
= (SSPCLKDIV (1 + SCR) CPSDVSR) / f
main
. The clock cycle time derived from the SPI bit rate T
cy(clk)
is a function of the
main clock frequency f
main
, the SPI peripheral clock divider (SSPCLKDIV), the SPI SCR parameter (specified in the SSP0CR0 register),
and the SPI CPSDVSR parameter (specified in the SPI clock prescale register).
[2] T
amb
= 40 C to 85 C.
[3] T
cy(clk)
= 12 T
cy(PCLK)
.
[4] T
amb
= 25 C; for normal voltage supply range: V
DD
= 3.3 V.
t
DS
data set-up time in SPI mode
[3][4]
0-- ns
t
DH
data hold time in SPI mode
[3][4]
3 T
cy(PCLK)
+ 4 - - ns
t
v(Q)
data output valid time in SPI mode
[3][4]
--3 T
cy(PCLK)
+ 11 ns
t
h(Q)
data output hold time in SPI mode
[3][4]
--2 T
cy(PCLK)
+ 5 ns
Table 18. Dynamic characteristics of SPI pins in SPI mode
Symbol Parameter Conditions Min Typ Max Unit
Pin names SCK, MISO, and MOSI refer to pins for both SPI peripherals, SPI0 and SPI1.
Fig 21. SPI master timing in SPI mode
SCK (CPOL = 0)
MOSI
MISO
T
cy(clk)
t
clk(H)
t
clk(L)
t
DS
t
DH
t
v(Q)
DATA VALID DATA VALID
t
h(Q)
SCK (CPOL = 1)
DATA VALID
DATA VALID
MOSI
MISO
t
DS
t
DH
DATA VALID DATA VALID
t
h(Q)
DATA VALID
DATA VALID
t
v(Q)
CPHA = 1
CPHA = 0
002aae829