Datasheet
Table Of Contents
- 1. General description
- 2. Features and benefits
- 3. Applications
- 4. Ordering information
- 5. Block diagram
- 6. Pinning information
- 7. Functional description
- 7.1 ARM Cortex-M0 processor
- 7.2 On-chip flash program memory
- 7.3 On-chip SRAM
- 7.4 Memory map
- 7.5 Nested Vectored Interrupt Controller (NVIC)
- 7.6 IOCONFIG block
- 7.7 Fast general purpose parallel I/O
- 7.8 UART
- 7.9 SPI serial I/O controller
- 7.10 I2C-bus serial I/O controller
- 7.11 C_CAN controller
- 7.12 10-bit ADC
- 7.13 General purpose external event counter/timers
- 7.14 System tick timer
- 7.15 Watchdog timer
- 7.16 Clocking and power control
- 7.17 System control
- 7.18 Emulation and debugging
- 8. Limiting values
- 9. Static characteristics
- 10. Dynamic characteristics
- 11. Application information
- 12. Package outline
- 13. Soldering
- 14. Abbreviations
- 15. Revision history
- 16. Legal information
- 17. Contact information
- 18. Contents
LPC11CX2_CX4 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 3.1 — 15 May 2013 18 of 62
NXP Semiconductors
LPC11Cx2/Cx4
32-bit ARM Cortex-M0 microcontroller
7.8 UART
The LPC11Cx2/Cx4 contain one UART.
Support for RS-485/9-bit mode allows both software address detection and automatic
address detection using 9-bit mode.
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
7.8.1 Features
• Maximum UART data bit rate of 3.125 Mbit/s.
• 16 Byte Receive and Transmit FIFOs.
• Register locations conform to 16C550 industry standard.
• Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
• Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• FIFO control mechanism that enables software flow control implementation.
• Support for RS-485/9-bit mode.
• Support for modem control.
7.9 SPI serial I/O controller
The LPC11Cx2/Cx4 contain two SPI controllers. Both SPI controllers support SSP
features.
The SPI controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SPI supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
7.9.1 Features
• Maximum SPI speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
• Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
• Synchronous serial communication
• Master or slave operation
• 8-frame FIFOs for both transmit and receive
• 4-bit to 16-bit frame
7.10 I
2
C-bus serial I/O controller
The LPC11Cx2/Cx4 contain one I
2
C-bus controller.