Datasheet
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 3 — 16 December 2013 7 of 23
NXP Semiconductors
74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
[1] Typical values are measured at T
amb
= 25 C.
I
CC
supply current V
I
= V
CC
or GND; V
is
= GND or V
CC
;
V
os
=V
CC
or GND
V
CC
= 6.0 V - - 20.0 A
V
CC
= 10.0 V - - 40.0 A
C
I
input capacitance - 3.5 - pF
C
sw
switch capacitance - 8 - pF
T
amb
= 40 C to +125 C
V
IH
HIGH-level input voltage V
CC
= 2.0 V 1.5 - - V
V
CC
= 4.5 V 3.15 - - V
V
CC
= 6.0 V 4.2 - - V
V
CC
= 9.0 V 6.3 - - V
V
IL
LOW-level input voltage V
CC
= 2.0 V - - 0.50 V
V
CC
= 4.5 V - - 1.35 V
V
CC
= 6.0 V - - 1.80 V
V
CC
= 9.0 V - - 2.70 V
I
I
input leakage current V
I
= V
CC
or GND
V
CC
= 6.0 V - - 1.0 A
V
CC
= 10.0 V - - 2.0 A
I
S(OFF)
OFF-state leakage current V
CC
= 10.0 V; V
I
= V
IH
or V
IL
;
V
SW
=V
CC
GND; see Figure 8
per channel - - 1.0 A
I
S(ON)
ON-state leakage current V
CC
= 10.0 V; V
I
= V
IH
or V
IL
;
V
SW
=V
CC
GND; see Figure 9
--1.0 A
I
CC
supply current V
I
= V
CC
or GND; V
is
= GND or V
CC
;
V
os
=V
CC
or GND
V
CC
= 6.0 V - - 40 A
V
CC
= 10.0 V - - 80 A
Table 7. Static characteristics 74HC4066-Q100
…continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
V
is
is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
V
os
is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ
[1]
Max Unit
Table 8. Static characteristics 74HCT4066-Q100
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
V
is
is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
V
os
is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ
[1]
Max Unit
T
amb
= 40 C to +85 C
V
IH
HIGH-level input voltage V
CC
= 4.5 V to 5.5 V 2.0 1.6 - V
V
IL
LOW-level input voltage V
CC
= 4.5 V to 5.5 V - 1.2 0.8 V
I
I
input leakage current V
I
= V
CC
or GND; V
CC
= 5.5 V - - 1.0 A