User Manual

ManualsBrandsNXP Laboratories UK ManualsAudio EquipmentIEEE 802.15.4 Wireless Microcontroller

Table Of Contents

1 Introduction
- 1.1 Wireless Transceiver
- 1.2 RISC CPU and Memory
- 1.3 Peripherals
- 1.4 Block Diagram
2 Pin Configurations
- 2.1 Pin Assignment
- 2.2 Pin Descriptions
3 CPU
4 Memory Organisation
- 4.1 ROM
- 4.2 RAM
- 4.3 OTP eFuse Memory
- 4.4 External Memory
  - 4.4.1 External Memory Encryption
- 4.5 Peripherals
- 4.6 Unused Memory Addresses
5 System Clocks
- 5.1 16MHz System Clock
  - 5.1.1 32MHz Oscillator
  - 5.1.2 24MHz RC Oscillator
- 5.2 32kHz System Clock
6 Reset
- 6.1 Internal Power-on Reset
- 6.2 External Reset
- 6.3 Software Reset
- 6.4 Brown-out Detect
- 6.5 Watchdog Timer
7 Interrupt System
- 7.1 System Calls
- 7.2 Processor Exceptions
- 7.3 Hardware Interrupts
8 Wireless Transceiver
- 8.1 Radio
  - 8.1.1 Radio External Components
  - 8.1.2 Antenna Diversity
- 8.2 Modem
- 8.3 Baseband Processor
- 8.4 Security Coprocessor
- 8.5 Location Awareness
- 8.6 Higher Data Rates
9 Digital Input/Output
10 Serial Peripheral Interface
11 Timers
- 11.1 Peripheral Timer/Counters
- 11.2 Tick Timer
- 11.3 Wakeup Timers
  - 11.3.1 RC Oscillator Calibration
12 Pulse Counters
13 Serial Communications
- 13.1 Interrupts
- 13.2 UART Application
14 JTAG Debug Interface
15 Two-Wire Serial Interface
- 15.1 Connecting Devices
- 15.2 Clock Stretching
- 15.3 Master Two-wire Serial Interface
- 15.4 Slave Two-wire Serial Interface
16 Four-Wire Digital Audio Interface
17 Random Number Generator
18 Sample FIFO
19 Intelligent Peripheral Interface
- 19.1 Data Transfer Format
- 19.2 JN5148 (Slave) Initiated Data Transfer
- 19.3 Remote (Master) Processor Initiated Data Transfer
20 Analogue Peripherals
- 20.1 Analogue to Digital Converter
- 20.2 Digital to Analogue Converter
  - 20.2.1 Operation
- 20.3 Comparators
21 Power Management and Sleep Modes
- 21.1 Operating Modes
  - 21.1.1 Power Domains
- 21.2 Active Processing Mode
  - 21.2.1 CPU Doze
- 21.3 Sleep Mode
- 21.4 Deep Sleep Mode
22 Electrical Characteristics
- 22.1 Maximum Ratings
- 22.2 DC Electrical Characteristics
- 22.3 AC Characteristics
Appendix A Mechanical and Ordering Information
- A.1 56-pin QFN Package Drawing
- A.2 PCB Decal
- A.3 Ordering Information
- A.4 Device Package Marking
- A.5 Tape and Reel Information
Appendix B Development Support
- B.1 Crystal Oscillators
- B.2 32MHz Oscillator
- B.3 32kHz Oscillator
- B.4 JN5148 Module Reference Designs
  - B.4.1 Schematic Diagram
  - B.4.2 PCB Design and Reflow Profile
- Related Documents
- RoHS Compliance
- Status Information
- Disclaimers
- Version Control
- Contact Details

Jennic

74 JN-DS-JN5148-001 1v2 © Jennic 2009

Preliminary

22.3.16 Radio Transceiver

This JN5148 meets all the requirements of the IEEE802.15.4 standard over 2.0 - 3.6V and offers the following

improved RF characteristics. All RF characteristics are measured single ended.

This part also meets the following regulatory body approvals, when used with Jennic’s Module Reference Designs.

Compliant with FCC part 15, rules, IC Canada, ETSI ETS 300-328 and Japan ARIB STD-T66

 The PCB schematic and layout rules detailed in Appendix

B.4 must be followed. Failure to do so will likely result in the

JN5148 failing to meet the performance specification detailed

herein and worst case may result in device not functioning in the

end application.

Parameter Min Typical Max Notes

RF Port Characteristics

Type Single Ended

Impedance

50ohm 2.4-2.5GHz

Frequency range 2.400 GHz 2.485GHz

ESD levels (pin 17) TDB

1) With external matching inductors and assuming PCB layout as in Appendix B.4.