User Manual

18 JN-DS-JN5142-x01-Myy 1v0 © NXP Laboratories UK 2012
A.7.1 Antennas approved by FCC for use with JN5142 modules
Brand
Model Number
Description
Gain (dBi)
Connector type
1
Antenna Factor
ANT-2.4-CW-RCT-RP
Vertical - knuckle antenna
2.2
RP-SMA
2
Antennova
2010B6090-01
Vertical - knuckle antenna
2.2
RP-SMA
3
Hyperlink Technology
HG2402RD-RSF
Vertical - knuckle antenna
2.2
RP-SMA
4
Aveslink Technology, Inc
E-0005-AC
Vertical- flying lead
2
RP-SMA
5
Aveslink Technology, Inc
E-2411-GC
Vertical - swivel
2
RP-SMA
6
Aveslink Technology, Inc
E-2410-CA
Vertical - bulkhead- flying lead
2
uFL
7
Aveslink Technology, Inc
E-2410-GC
Vertical - swivel
2
RP-SMA
8
Aveslink Technology, Inc
E-2820-CA
Vertical - bulkhead- flying lead
2
uFL
9
Aveslink Technology, Inc
E-2820-GC
Vertical - swivel
2
RP-SMA
10
Aveslink Technology, Inc
E-0903-AX
Embedded - nickel silver strip
2
None
11
Aveslink Technology, Inc
E-0904-AX
Embedded - nickel silver strip
2
None
12
Embedded Antenna Design
FBKR35068-RS-KR
Vertical - knuckle antenna
2
RP-SMA
13
Nearson
S131CL-L-PX-2450S
Vertical - knuckle-flying lead
2
uFL
14
Laird Technologies
WRR2400-IP04
Vertical - knuckle-flying lead
1.5
uFL
15
Laird Technologies
WRR2400-RPSMA
Vertical - knuckle-flying lead
1.3
RP-SMA
16
Aveslink Technology, Inc
E-6170-DA
Vertical - right angle
1
uFL
17
Laird Technologies
WCR2400-SMRP
Vertical - knuckle antenna
1
RP-SMA
These antennae or versions with alternative connectors may be used to meet European regulations.
This device has been designed to operate with the antennas listed above, and having a maximum gain of 2.2 dBi.
Antennas not included in this list or having a gain greater than 2.2 dBi are strictly prohibited for use with this device.
The required antenna impedance is 50 ohms.
A.7.2 FCC End Product Labelling
The final „end product‟ should be labelled in a visible area with the following:
“Contains TX FCC ID: TYOJN5142M0 or TYOJN5142M3” to reflect the version of the module being used inside the
product.
A.8 Industry Canada Statement
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
These modules have been designed to operate with antennas having a maximum gain of 2.2 dBi. Antennas having a
gain greater than 2.2 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc).
A.8.1 Industry Canada End Product Labelling
For Industry Canada purposes the following should be used.
“Contains Industry Canada ID IC: 7438A-CYO5142M0 or IC: 7438A-CYO5142M3” to reflect the version of the module
being used inside the product.