User Manual

Jennic
JennicJennic
Jennic
© Jennic 2009 JN-DS-JN5139-xxx-Myy 1v5 3
1. Introduction
The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1]
wireless applications, using Jennic’s JenNet networking protocol or ZigBee, to be quickly and easily included in
product designs. The modules integrate all of the RF components required, removing the need to perform expensive
RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins.
The modules use Jennic’s single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the
extensive chip development support material. Hence, this range of modules allows designers to bring wireless
applications to market in the minimum time with significantly reduced development effort and cost.
Three module hardware variants are available: JN5139-xxx-M00 (standard module with on board ceramic antenna),
JN5139-xxx-M01 (standard module with SMA connector for use with external antennae – recommended for
evaluation use) and JN5139-xxx-M02 (high RF power, improved sensitivity module for evaluation of extended range
applications). For volume production applications, uFL connector variants are provided (-M03 standard power and –
M04 high power). These devices, together with the –M00 variants have FCC modular approvals. Each of these
modules can be supplied with a range of protocol stacks, including JenNet for most tree and linear networks,
IEEE802.15.4 protocol for point-to-point and star applications and a ZigBee mesh networking stack. The variants
available are described below.
1.1. Variants
1.2. Regulatory Approvals
All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a
Notified Body statement of opinion for this standard is available on request. The High Power modules with M02 or
M04 suffix are approved for use in Europe with reduced output power: +10dBm EIRP is the maximum permitted in
Europe. They must not be used with PHY_PIB_ATTR_TX_POWER set above 50 See [3] JN-RM-2002 802.15.4
Stack API.
Additionally, modules with M00, M03 and M04 suffixes have received FCC “Modular Approvals”, in compliance with
CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407. The modules are approved for
use with a number of antennase, refer to section A.6.1 for details. See Appendix A.6 for details on the conditions
applying to this modular approval. The modular approvals notice and test reports are available on request.
The high power module variant is classified as ‘mobile’ device pursuant with FCC § 2.1091 and must not be used at a
distance of less than 20 cm (8”) from any person.
In addition, all modules have Industry Canada RSS 210 Issue 7 (June 2007) certification.
Variant Description FCCID Industry Canada ID
JN5139-001-M00 IEEE802.15.4 stack, ceramic antenna TYOJN5139M0
IC: 7438A-CYO5139M0
JN5139-Z01-M00 ZigBee stack, ceramic antenna TYOJN5139M0
IC: 7438A-CYO5139M0
JN5139-001-M01
IEEE802.15.4 stack, SMA connector - for
evaluation
N/A
IC: 7438A-CYO5139M6
JN5139-Z01-M01
ZigBee stack, SMA connector – for
evaluation
N/A
IC: 7438A-CYO5139M6
JN5139-001-M02
High Power, IEEE802.15.4 stack, SMA
connector – for evaluation
N/A
IC: 7438A-CYO5139M4
JN5139-Z01-M02
High Power, ZigBee stack, SMA connector
– for evaluation
N/A
IC: 7438A-CYO5139M4
JN5139-001-M03 IEEE802.15.4 stack, uFl connector TYOJN5139M3
IC: 7438A-CYO5139M6
JN5139-Z01-M03 ZigBee stack, uFl connector TYOJN5139M3
IC: 7438A-CYO5139M6
JN5139-001-M04
High Power, IEEE802.15.4 stack, uFl
connector
TYOJN5139M4
IC: 7438A-CYO5139M4
JN5139-Z01-M04 High Power, ZigBee stack, uFl connector TYOJN5139M4
IC: 7438A-CYO5139M4