NX-SO OUND DBAR R-40 40 0-Wa att Stereo o Sou und Bar Own ners Ma anual nxgtechnolo ogy.
Congratulations on your purchase of the NXG Technology NX-SOUNDBAR-40 Stereo Sound bar! Like all NXG products, great care has been taken in its design. A combination of advanced engineering and state-of- the-art materials will provide you with years of listening pleasure. The NX-SOUNDBAR-40 allows you to play stereo audio from any Bluetooth enabled device including TVs, Smart Phones, Tablets, or any device with an analog or optical output. IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE.
Pla acementt Ven ntilation Wh hen placin ng the Sou und bar on an ente ertainment center, bookshelf b f, or any typ pe of enclo osed spac ce, be surre to allow w at least 2-3 inchess of space e around the e unit for ventilation v . If the unit is enclosed in a tiight space e, withoutt ven ntilation, heat h gene erated ca an produc ce a poten ntial hazard.
REMOTE CONTROL BUTTON LAYOUT 1. POWER: Press to turn the Sound bar off or on. 2. CLOCK: Press to set the time. 3. SOURCE: Press to switch between Bluetooth, FM, AUX in and optical in. 4. TUNE BACK: Press to tune the FM radio. This button is for radio only. 5. VOL-: Press to reduce the volume. 6. SEARCH DOWN: Press to navigate down radio stations. This button is for radio only. 7. EQ: Press to select FLAT, ROCK, JAZZ, POP and CLASSICAL. 8. MUTE: Press to mute the volume. 9. ALARM: Press to set the alarm. 10.
Listening to a Saved Radio Station 1. Press the SOURCE button to switch to FM radio mode. 2. Press the UP and DOWN buttons on the remote to cycle through saved radio stations. Saving a Radio Station 1. After tuning to the desired station, press the MEM button. 2. Press the UP or DOWN buttons on the remote to select a preset number. 3. Press the MEM button to save the current radio station to the selected preset. Up to 20 stations can be saved to the Sound bar’s memory.
Hooking it up You can connect your TV or other external device to the Sound bar in several ways: ANALOG Wired Connection 1. Plug the 3.5mm end of either the RCA Audio Cable or the 3.5mm Audio Cable into the AUX IN located on the back of the Sound bar. 2. Plug the other end into the source device (TV, Phone, MP3 Player, etc.). 3. Press the SOURCE button repeatedly to select AUX as the input. 4. Once the device is hooked up, you can control playback as you would usually on the source device.
Wall Mounting Using the included wall mounting accessories, the sound bar can be easily mounted onto a wooden or sheet-rock wall. Distance Between Brackets 24” 24 inches Tools Needed: A Bubble Level, Pencil, Drill, Tape Measure, and a Philips Screw Driver 1. Determine how high you’d like to hang the Sound Bar on the wall. Seated Ear-Level is usually a good guide – Note: The Sound Bar must be hung within 5 feet of an AC power outlet (or power strip) for the attached AC power cord to reach. 2.
Troubleshooting: Problem No power No sound No soundfrom Bluetooth connection Solution Check that the power is switched on at the wall. Check if the power cord is properly connected to the power outlet. Check that the volume control is NOT at minimum setting. Check that it is NOT set to mute. Check if you have properly paired with the source - pairing code 0000 If none of the above solutions work, then switch off and unplug your Speaker system, leaving it for 2 minutes and then switching it back on again.
Box Contents: Input Cables (RCA & 3.5mm) Power Supply Wall mounting Screws x2 Wallmount Anchors x2 NX-SOUNDBAR-40 Stereo Sound bar Foam Spacers x2 (for wall mounting) POWER Remote Control 8 nxgtechnology.
