V1 NX-MOUNT-ART-L Large Full Motion Mount INSTRUCTION MANUAL CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
Congratulations on the purchase of your new TV Mount. At NXG Technology we design our products to be simple to use, durable, & furnctional. Like all NXG products, our mount line has evolved from hours of rigorous testing by our engineers and customers and were designed to provide you with years of enjoyment. Please take a moment to review the installation instructions to ensure that you get the most from your new mount. support@nxgtechnology.
HARDWARE PRODUCT NUMBERS 1 M4 x 12 X4 2 M5 x 12 X4 3 M6 x 15 X4 4 M8 x 15 X4 5 M4 x 25 X4 6 M5 x 25 X4 7 M6 x 25 X4 8 M8 x 25 X4 Adapter Hardware 9 SQUARE WASHER X4 10 13 5mm SPACER X8 11 8 mm LAG BOLT X4 12 STEEL WASHER X4 ANCHOR X4 A1 A2 A3 A4 SECURITY ALLEN WRENCH 4 mm M6 X 5/8” X8 WRENCH M6 WASHER X2 M6 ACORN NUT X2 PRODUCT COMPONENT PARTS Universal Adapter Range Minimum: 200mm x 100mm (W X H) Maximum: 600mm x 400mm (W X H) A B C Product Components Contents A B C Qty Descrip
PRODUCT DIMENSIONS AND SPECIFICATIONS 60 lbs MW60C44 P4
CORNER MOUNTING INFORMATION The Large Full Motion Mount can be installed in a corner location when needed. Prior to installing the Mount it is important to determine the appropriate corner wall to install the mount. Please see diagrams below to assist in determining the appropriate wall placement to use. Drawings below show the Large Full Motion Mount attached to the left and right of the corner. Depending on the desired angle for viewing, please review to determine which wall to mount your panel.
STEP 1- FLAT BACK FLAT PANEL (UNIVERSAL MONITOR PLATE) Connect Universal Monitor Plate to flat panel SQUARE WASHER X4 9 9 1 2 3 4 B X4 STEP 1- CURVED BACK FLAT PANEL (UNIVERSAL MONITOR PLATE) Connect Universal Monitor Plate to flat panel SQUARE WASHER X4 10 9 9 5 10 6 7 8 Spacers can also be used to provide clearance for cables and connectors.
STEP 1- CENTER UNIVERSAL MONITOR PLATE Monitor Plate must be centered (horizontal plane) on back of flat panel STEP 1- SECURE UNIVERSAL MONITOR PLATE VERTICAL RAILS Secure vertical rails to horizontal chrome rod on Monitor Plate with pre-installed screws.
STEP 2- PRIOR TO EXTENDING ARMS REMOVE ARM ASSEMBLY FROM WALL PLATE Prior to extending arms remove 2 security screws with security Allen wrench to remove Arm Assembly from Wall Plate. Note- 2 security screws will be used in Step 4 to reattach arm assembly to wall mount. Remove Arm Assembly by gently lifting vertically off Wall Plate. Wall Plate is now ready to attach to wall surface (Step 3).
STEP 3A- WOOD STUD INSTALLATION (CONCRETE INSTALLATION SKIP TO 3B) Find stud and mark edge and center locations Ubique el panel y marque las ubicaciones de los bordes y el centro. Repérez l'emplacement d'une poutre, puis marquez l'emplacement des bords et du centre de cette poutre.
STEP 3B – SOLID CONCRETE INSTALLATION Solid Concrete Drill Bit Concreto sólido Béton massif Level Drill pilot hole S.
STEP 4- ATTACH MOUNT ASSEMBLY TO WALL PLATE Position Arm Assembly to desired lateral position on wall plate for optimum placement of Flat Panel. Secure Arm Assembly to Wall plate using 4mm Security Allen Key.
SECURE MONITOR PLATE TO ARM ASSEMBY Secure Acorn Nut and Washer on Monitor Plate to Arm Assembly A3 (snug tension only) A4 A3 M6 Washer A4 M6 Acorn Nut A2 M6 Wrench A2 B X2 ADJUST TILT TENSION/ POST INSTALLATION LEVEL Adjust tilt mechanism tension with ratchet handle Built-in level feature for post installation correction Ratchet handle for tensioning tilt mechanism. Rotate clockwise to Tension Tilt Mechanism.
WARRANTY INFORMATION Manufacturer warrants this product against defects in material or workmanship for the original purchaser of the product with the following conditions: WARRANTY PERIOD: "The three-Year Limited Manufacturer’s Warranty” covers this product against defects in materials or workmanship from the date of purchase by the original consumer for a period of three (3) years for parts and labor.
