Instruction Manual

ManualsBrandsnVent ManualsPlatenVent Eriflex FleXbus HCBC Clamp and Plate for Connection

Table Of Contents

≈170

Min. 10mm

≈100

Min. 10mm

≈170

Min. 10mm

100A

100B

100C

50A

50B

50A

50B

100A

100B

100C

≈5

FLEXPLATE100

(508181)

FLEXPLATE50

(508180)

FLEXPLATE100PE

(508183)

FLEXPLATE50PE

(508182)

FLEXCLAMP63(508190) FLEXCLAMP120(508193)

FLEXCLAMP80 (508191) FLEXCLAMP160(508194)

FLEXCLAMP100(508192)

2.1

USE FLEXCLAMP

ONE CONDUCTOR

TWO CONDUCTOR

220 to 1280mm²

1810mm²

2x 960 to 1810 mm²

TECHNICAL SUPPORT

www.nVent.com

IP8596_J

1 OF 4

INSTRUCTION SHEET

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by

nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change

specifications without prior notice.

WARNING:

nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at

www.nVent.com

and from your nVent customer service representative.

nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and/or death, and void your warranty.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.





Reserved

Summary of content (4 pages)

PAGE 1
INSTRUCTION SHEET   1 m m 10m 10m FLEXCLAMP63(508190) FLEXCLAMP80 (508191) FLEXCLAMP100(508192) 2 2.1 FLEXPLATE50(508180) 50A 50B FLEXCLAMP120(508193) FLEXCLAMP160(508194) FLEXPLATE100 (508181) 100A 100B 100C PIN USE FLEXCLAMP 50B 100A 100B 100C ≈5 50A PIN FLEXPLATE50PE (508182) FLEXPLATE100PE (508183) WARNING: 1.
PAGE 2
INSTRUCTION SHEET   Typical usage for Oil Transformer Typical usage for Dry/Cast resin Transformer Trans- In Transformer former type (A) HCBC Clamp & Plate mounting Transformer palm dimensions (mm) HCBC Clamp & Plate mounting per phase EN 50387 PALM 1 400 kVA Transformer palm dimensions (mm) DIN 42530 PALM 6 630 kVA 704 63 900 1pc FLEXCLAMP 63 1pc FLEXPLATE 50(PE) PALM 7 800 kVA 1120 100 PALM 2 1000 1400 kVA 63 PALM 3 1250 1750
PAGE 3
INSTRUCTION SHEET   MOUNTING PIN 50B PALM 1 - PALM 2 100B PALM 3 PALM 4 PALM 5 50A PALM 6 PALM 7 PALM 8 PALM 9 PALM 10 PALM 11 50B 50A PALM 12 PALM 13 PALM 14 PALM 15 PALM 16 PALM 17 50B 50B 50A or 100B PALM 18 PALM 19 50B 100B or 100C 100C 100C 100A 100A 50A 50A or 100A 100A 100A 50B 50A 100B or 100C 100A 100A 50B 50B 50A or 100C 100A 100A 100B - - - 1 - 2.
PAGE 4
INSTRUCTION SHEET   Ø 5.2 FLEXPLATE50PE FLEXPLATE100PE Ø1 Ø1 Ø2 10.5 14.5 12.5 16.5 The minimum clearance distrance is 14mm according IEC 61439-1 with air pollution degree 3. Ø2 nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners.