Wireless Security & Safety System HG-1000 OWNER’S MANUAL
Table of Contents Introduction (HG-1000) … … … … … … … … … … … … … … … … … … … … … … … … … .. System Package … … … … … … … … … … … … … … … … … … … … … … … .. Optional Accessories … … … … … … … … … … … … … … … … … … … … … .. Planning for Installation … … … … … … … … … … … … … … … … … … … … … … … … … . Choosing Location … … … … … … … … … … … … … … … … … … … … … … ..
Important Safety Instruction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE OR POWER ADAPTER TO WATER OR MOISTURE • • • • • • • • • Read Instructions – All the safety and operating instructions should be read before operating this equipment. These instructions should be retained for future reference Heed Warnings – All warnings on the equipment and in the operating instructions should be adhered to.
Introduction Thank you for choosing our wireless home security system. This Security System is high-quality, reliable and versatile security system. This system built in Auto-dialer function. To ensure the best performance of your system, please read this manual thoroughly and follow the precautions and instructions presented. These systems are designed to be simple and easy to install and maintain. Wireless easy to use : No messy and expensive wiring is required to install the system.
Planning for Installation AWAY HOME PANIC DISARM ARMED POWER 1 2 3 4 5 6 7 8 9 0 # MICROPROCESSOR CONTROL KEYPAD The security system is designed to be as flexible as possible in order to meet your present needs, and also to adapt as your needs change. For the reason, we recommend that you read and consider the following information and plan your system before installing devices. Choosing Location It is important to try and place the Main Console in an area central. This way.
Connecting the Telephone Line To correct the Main Console to the telephone line, Please follow these steps: 1. 2. 3. 4. Locate the two phone jacks on the back inside of the main console. These phone jacks are marked “ Phone “ and “ Line “. Connect one end of the telephone cord that came with the system into the connector labeled Line. Connect the other end of that cord into the wall jack. Connect a telephone to the Main Console through the phone jack. Set the back cover and fix it securely.
About the Main Console operation The Main Console is the heart of the security system. It monitors the sensors and the responds according to how it is programmed, whenever the sensor is activated. The controls shown on the Main Console may look complex at the first sight, however, most procedures are straightforward and easy. Please review the illustration below which labels all of the parts of the Main Console.
12. Power LED : Indicates the AC Adaptor power is on or off. 13. Armed LED 14. LCD Panel : When the light ‘on’, system is armed; the light ‘off’, system is disarmed. : Display the message 15. Speaker 16. Antenna 17. Output Jack 18. Phone Jack 19. Line Jack 20.
Function for Installer – Factory Default Password :123456 1. Enter password to start the menu. LCD shown as below(Enter the password and do the function setting according to your need) Code : ****** l Incorrect password entering will show “ Access Denied” and will emit beep sound warning. Access Denied l If 3 incorrect password are entered, keyboard disabled and locked (LCD shown as below). Try it again after one minute idle or use Remote Control Handset ( DISARM button) to disarm the system.
Press 1 button, setting delay time for exiting house. The default time is 30 Sec, you can set the time from 1 to 255 Sec. Press Enter button to finish the setting. Setting : 1 – Exit Time : 30 Sec Press 2 button, setting alarm time for triggering alarm, The default time is 30 Sec, you can set the time from 1 to 255 Sec. Press Enter button to finish the setting.
When finished recording message, it will automatically playback recorded message one time and LCD panel shown as below. Setting : Sel Msg (4) Message Play : 1 25 Sec 8 – DIAL : To set Dial mode. (default is 2-ALL to dial all telephone sets) Setting : Dialer Mode 1 – Single 2 – All 2 2 Press 1 for single attempt dial. ( if one of the telephone set is acceptable, it will stop to dial other’s telephone set) Setting : Dialer Mode 1 – Single 2 – All 1 Press 2 for 3 cycles attempt dial.
to set Zone numbers maximum to 63 addresses. It is recommend that you use a pen on the sensor back label to mark the sensor location, You can also replace or clear sensor for changing sensor. In the system menu, SYS_OPTS: 0-SYS_OPTS 1 – SEQ 2 – REPLAC 3 – CLR Press 1 and into the sequential programming mode Sequential Trigger Pgming Sensor 01 ( 01 sensor learning order) The method for sensors learning: 1. 2. 3. 4. 5. 6. 7.
9. If sensors have learned and reach 63 zone numbers, LCD panel shows memory full message. Sequential Mem Full Pgming 63 NOTE :1. Sensors belong to 24 hours included: Smoke Detector, Gas Detector, Panic Watch, Remote Control Handset(PANIC button) 2. Distinguish A-AWAY and H-HOME mode: When system is armed in HOME mode, Main Console will neglect the transmission signal from the PIR Detector. 2-REPLAC : To replace the sensor.
3-CLR : Clear Sensors ( 1 - Single 2 – All ) Select 1- Single, you can key-in learned sensor order code and press It will clear the sensor. If select 2- All, It will clear all learned sensors. Press 3 and go into clear mode. Clear Sensor 1 – Single Press 1 ENTER . 2 - All and key-in learned sensor order code then press ENTER ,It will clear this sensor. Clear Sensor 1 – Single Num: xx Clear Sensor Clear OK Num : xx Press 2 , It will show the “Are you sure ? ”. press learned sensors.
Function for Master – Factory Default Password – 135246 1. To enter Master code – 135246, LCD display shown as below 00 HOME SECURITY Disarmed Code : l ****** When the password is incorrect, It will introduce Beep … Warning sound. LCD display shown as below. Access l Denied If the password is correct, It will introduce a long Beep sound. LCD display shown as below.
signal from the PIR Detector. Check Function To press CHECK button to check the memory data you have installed previously without any password, but you can only review not allow to change the data in ‘Check’Mode. Following with the menu structure as below. Check : 0 – T 1 2 3 4 5 6 –P 7 – MSG 8 – DIAL Check : 0–T 123456 – P 7 – MSG 8 – DIAL : To review (1- Exit) Exit time, (2-Alarm) Alarm time, (3- Entry) Entry time. : To review phone number sets. : To review recorded message : To review dial mode.
Auto-dialer priority This system stores up to six (6) telephone numbers in the Main Console. If it is triggered and alarm is activated, the auto-dialer will call the pre-set 4 sets telephone numbers and play your pre-recorded message. If system is triggered Burglary help - It will automatically dial phone 4 → phone 1 → phone 2 → phone 3 call sequentially by 3 cycles attempt (4, 1, 2, 3).
Remote Control Handset The key chain Remote Control Handset is a convenient way to arm ( Home / Away mode) or disarm this system. Before using the sensor, it is necessary to learn into main console. DC12V LEGEND 1. TRANSMIT LED 2. DISARM KEY 3. AWAY KEY 4. HOME KEY 5. PANIC KEY 6. BATTERY 1. 2. 3. 4. 5. 6.
P.I.R Motion Detector The PIR Motion Detector is designed to detect the movement of object in rooms or hallway. The effective range of the motion sensor is 30 feet long, and with an 84 degree horizontal angle. Before using the sensor, the sensor needed to be learned into main console. If main console is armed in HOME mode. Even if PIR Triggered, the main console will neglect the PIR signal. Main Features : 1. 2. 3. 4. 5. 6. LED : When PIR has detected any moving of human.
Replace the Battery l When the sensor send the low battery voltage signal to main console. Please replace a new battery for the sensor. In the main console, the LCD display shown the message as below 63 PIR SENSOR 01 Low battery Zone Address Setting Enter the Installer password and the main console is in learning mode, after installing the battery on the PIR. Set the power switch from “ OFF ” to “ C ” position.
Installing the Motion Sensor Before installing the sensor, consider the following points: l Mount the sensor at two meters (6-1/2’) high for best coverage. Mount the sensor with a 14 degree downward incline against the wall for optimum range. l To install the Motion Sensor, please follow these steps: l l l Take out the screws or double sided adhesive and install the mounting bracket on the wall. press the ball joint portion into the bracket until it snaps securely.
Door/Window Detector The magnetic Door/Window detector is a contact sensor applied on door or window. When the magnetic contact is opened (broken) or the battery is in low level, the sensor will send out the signal to main console. The message of the triggered sensor can be read from the Main Console’s LCD display. Door/Window Detector (for DC 12V battery) Button Function: 1.Magnet 2.Transmit LED : When the sensor is activated, LED will light for 1 sec. 3.Magnet Sensor 4.
Zone address setting You can set the sensor as “ Door “ or “ Window “ detector by using the jumper selector and follow the marked. Ex. You want to set the sensor as Door sensor, put the Jumper on marked “D” side. (If set Jumper on marked “W” side, the sensor becomes as Window sensor). DOOR / WINDOW SELECT DOOR / WINDOW SELECT TYPE SEL JUMPER DOOR TYPE SEL JUMPER DOOR DC 12V DC 9V WINDOW WINDOW Notes on the Door/Window Detector 1. 2. The LED on the sensor will flash once when the sensor is triggered.
63 63 WINDOW SENSOR 01 Tamper DOOR SENSOR 01 Tamper Installing the Door/Window Detector Installing for( DC 12V Detector): To install a Door/Window Detector, follow these steps: 1. Before installing the sensor, ensure the sensor has learned in main console successfully 2. Apply double aided adhesive tape to the back of the sensor. 3. Find the arrow embossed on the sensor, just below the LED light. Find a similar arrow on the magnet.
Mini Siren The mini siren is an optional accessory but suggested to be a part of standard package. The siren is an effective deterrent to intruders. To choose a location inside your home where the siren will not be plainly visible but can be heard throughout the house. Also, it is important to install the siren where the cable can be hidden, and discreetly out of reach of potential intruders (or anyone likely to tamper with the system.
Summary of Main Console programmed Use the following form to record your programming choices for future reference. Item Descriptions Install Code Master Code Exit Time Alarm Time Entry Time Auto-dialing Mode Sensor No. of Learning Preset Telephone No. for Auto-dialing : No. 1 Name Tel. No. No. 2 Name Tel. No. No. 3 Name Tel. No. No. 4 (Burglary Emergency) Name Tel. No. No. 5 (Fire Emergency) Name Tel. No. No. 6 (Help Emergency) Name Tel. No.
Specifications of Security System Items Specifications Frequency - 303Mhz or 433Mhz Power Source - AC120V, DC 12V or AC 230V DC12V Power Consumption - 70mA (idle), 170mA (activated) Back-up Battery (Optional) - Approximate 7 hours ( NO AC adaptor) Temperature Range - 0°C ∼ 40°C RF Range - 150 feet in open air space Security Code - Hopping code Alarm Activation Time - 1∼255 seconds (available alarm time setting) Dialing Type - Tone Voice Message Playing Time -Total 25 seconds Preset Tel
