WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION This equipment has been tested and found ta comply with the limits for 3 Class B digits! device pursuant to Part 15 of FCC Rules. Operation is subject to the following twa conditions: (1) This device may not cause harmful Interference, and (2) this device must accept any Interference received, Including Interference that may cause undesired operation.
Quick Start Quick Start Step 1: Step 2: Connect your guitar to OVERDRIVE/DISTORTION module Connect a guitar cable from the OUTPUT to instrument input. input on your amplifier. Step 3: Set all knobs to the 12 O'clock position. Make sure power switch is in power off position. Step 4: Connect power adapter to main power and to the power input on Cerberus.
Quick Start Step 5: ‘When Cerberus is in Manual mode, press foot switches to engage the effects. In Manual mode, the reverb effect cannot be engaged by pressing DELAY foot switch. There are two ways to turn on/off reverb separately: 1. Set the level knob of reverb fully left to turn off the reverb effect. 2. Assign CTR foot switch to reverb effect, turn on/off reverb effect. In Manual mode, the MOD FX effects and chorus effects will be engaged simultaneously when MOD effect foot switch is pressed.
Using the Effects Sets the gain of the drive. | Sets the gain of the dist. LEVEL: LEVEL: Sets volume of the drive. Sets volume of the drive. Cerberus allows you to choose among four different signal routing. A routing defines how the signal runs through the unit. To Switch among routing, press ROUTING switches. bits op bi St op DIST DIST On Serial Routing 1: The signal is going through the overdrive section first and then to the distortion section.
Using the Effects Cerberus use remarkable algorithm for highly accurate recreate of analog BBD circuit and the associated pulsating driver circuit. CE (Vintage Chorus) This models the first chorus effect pedal which was released in 1976. It has very warm and organic sound of an analog chorus unit. SC {Analog Chorus} This models the very popular chorus pedal in whole 80's. Original one was designed with only rate and depth control. We add level knob to control overall amount of chorusing.
Using the Effects Using the Effects SPR (Spring Reverb) This models a spring reverb inside a guitar amp. Use the level knob to adjust the mix ratio of the reverb sound. Use the decay knob to adjust the reverb time. PLA (Plate Reverb) This is a plate reverb that contains a brightness tone and natural reverb sound. HAL (Hall Reverb) This models a rather large hall and preserves the natural characteristics of guitar sound. Excellent for a discrete reverb with long reverb time.
Using the Effects BOOST knob (Volume Boost) soot To give you a boost of extra volume when you need it, the adjustable CTR foot switch delivers 20dB of extra volume. By adjusting the boost knob on the rear of the unit, you can preset the amount of boost you'd like the CTR foot switch to delver. Assigning the CTR foot switch functions om mm Here's how to assign the effects that will be turn & more ON/0ff by the CTR foot switch. eZ 1. Press the CTR button. 0 2.
Saving/Calling Up Preset Saving Tones You can perform preset-write operations either in Manual or in Preset mode. When performing a preset-write operation switches the unit into preset mode. 1. Press [SAVE] button, the pedal indicators flash. 2. Choose the preset number and letter where you'd like to save the patch by press BANK and preset {A through D) foot switches. 3. Press [SAVE] button again for saving. After a patch-write operation switches the unit into preset mode.
Other Functions Using External Expression Pedal An external expression pedal is used to manually control volume of Cerberus. The Volume parameter is positioned before the mod and delay sections. Calibrating Expression Pedals As different manufacturers deliver expression and volume pedals with varying potentiate types, it is important to calibrate the connectors on the Cerberus to the connected pedals for optimal performance. 1. Make sure that you have connected your pedal to the Exp. Jack. .
Appendices Effect types Effect modules Preset memory Display Sampling accuracy Processing accuracy THANT Frequency response @kHz Linotype Mono/Stereo Input Impedance Input level Maximum output level Latency 0.68ms 1/0 type Input Impedance Input level Maximum output level Ato A latency 20 Mono/Mono, GND LIFT Dimensions ~~ 320x110 x 65mm Weight Current consumption Options * bedbug = 0.775 Arms » Design and specifications are subject to change without notice.
