Installation Sheet

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE
CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow the
steps in the order given. Under no circumstances should a xture be hung
on house electrical wires, nor should a swag type xture be installed on
a ceiling which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualied
electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts are
included as shown in gure. Be careful not to misplace any of the screws or
parts, which are needed to install this xture.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Thread mounting screw into the match hole of cross bar.
STEP 2: Secure the cross bar to outlet box with outlet box screws.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised
dimples on the mounting cross bar. Wrap the ground wire from the xture (if
supplied) around the green grounding screw, then connect it to ground wire
from the outlet box (if not xed on the outlet box) using a wire connector (not
supplied). If ground wire from the xture is not supplied, wrap the ground
wire (if not xed on the outlet box) from the outlet box around the green
grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify which
group your xture wire(s) falls into and connect the wires according to the
directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square
shaped or ridged and the less tracer wire is round in shape or smooth (seen
best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against the
black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again for
a rm connection.
STEP 6: Connect the xture wire from group B to the white wire from
the outlet box in the same manner. Make sure no bare wires can be seen
outside wire connectors.
ITEM NO: 60-6564
ARTÍCULO Nº: 60-6564
ARTICLE N°: 60-6564
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet box.
Raise canopy allowing for the mounting screws to protrude through the
holes on canopy, use the ball nuts to fasten the canopy.
STEP 2: Install the bulbs (not included).
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do
not use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this xture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
Black Wire Connection
Ground Screw
Ball Nut
Bulb
Outlet Box
White Wire Connection
Universal Circle Cross Bar
Outlet Box Screw
Canopy
Mounting Screw