Installation Sheet

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING
ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER
IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow the steps
in the order given. Under no circumstances should a xture be hung on house
electrical wires, nor should a swag type xture be installed on a ceiling which
contains a radiant type heating system. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts are included
as shown in gure. Be careful not to misplace any of the screws or parts, which
are needed to install this xture.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Thread mounting screws (A) into the matching holes in the mounting
bar (B).
STEP 2: Secure the mounting bar (B) to outlet box with the outlet box screws (C)
(Not supplied).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples
on the mounting bar. Wrap the ground wire from the xture (if supplied) around
the green grounding screw, then connect it to ground wire from the outlet box
(if not xed on the outlet box) using a wire connector (not supplied). If ground wire
from the xture is not supplied, wrap the ground wire (if not xed on the outlet
box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify which
group your xture wire(s) falls into and connect the wires according to the
directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square
shaped or ridged and the less tracer wire is round in shape or smooth (seen
best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against the
black wire from the outlet box. Do NOT twist wires together before using wire
connectors.
STEP 4: Fit a wire connector over the wires and screw the connector clockwise
until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again for a
rm connection.
STEP 6: Connect the xture wire from group B to the white wire from the outlet
box in the same manner. Make sure no bare wires can be seen outside wire
connectors.
ITEM NO: 60-5931, 60-5942, 60-5961
ARTÍCULO Nº: 60-5931, 60-5942, 60-5961
ARTICLE N°: 60-5931, 60-5942, 60-5961
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet box.
Raise the canopy (D) allowing for the mounting screws (A) to protrude through
key slots. Rotate canopy (D) clockwise until mounting screws (A) are in narrow
part of key slots, tighten with screwdriver.
STEP 2: Thread the nut (F) onto the nipple (G) and thread the nipple (G) into
the coupling (E).
STEP 3: Install light bulbs (Not supplied). (Please do not exceed the maximum
capacity recommended on the socket.)
STEP 4: Place the metal frame (R) onto the shade (T)
STEP 5: Raise the shade (T) to the canopy (D), then secure with the screw (S).
STEP 6: Slide the tube (H), the cap (I), the metal washer (J), the plastic washer
(K), the glass (L), the plastic washer (M) and the metal washer (N) onto the nipple
(G), then secure with the nut (O).
STEP 7: Slide the cap (P) onto the nipple (G), then secure with the nial (Q).
NOTE: When you need to disassemble the glass from the xture, twist the glass
counter clockwise until the two red marks are at the same position.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do not use
abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement
parts. Be sure to use exact wording from illustration when ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.