Disclaimer • While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. • NUVICO reserves the right to change the specifications of the hardware and software described herein at any time without prior notice.
Warning and Caution WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT. CAUTION! The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Important Safeguards • Read these instructions. • Heed all warnings. • Follow all instructions. • Do not use this equipment near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other equipment (including amplifiers) that produce heat. • Do not defeat the safety purpose of the polarized or grounding-type plug.
Table of Contents Disclaimer .............................................................................................. Warning and Caution ............................................................................. Important Safeguards ............................................................................ Table of Contents ................................................................................... Introduction / Available Models ..........................................................
Introduction ABOUT THIS MANUAL Thank you for purchasing our EasyView™ Lite dome camera. Our EasyView™ Lite Dome Cameras are all equipped with high resolution 1/3” Interline transfer CCD Imager for enhanced lowlight sensitivity. Available in a host of different combinations, from standard fixed lens indoor color domes, to vari-focal day/night vandalproof dome, EasyView™ Lite series cameras accommodate a broad range of applications and demanding environments.
Content Verification Before installing the camera, please make sure that all of the following items are included in the box. EasyView™ Lite Dome CAMERA 1. EasyView™ Lite Dome Camera 2. Installation Manual 3. Surface Mount Mounting Template 4. Service Monitor Cable - Model#: CA-SMC30 (Vari-focal Lens models only) 5. Mounting Hardware • (x1) Torx Wrench (Vandalproof Only) • (x4) Philips ST4x30 Assembly Screws These screws are used to mount the Surface Mount Plate to a sturdy surface.
Parts & Descriptions 5 4 1 2 3 3 4 10 2 5 6 7 6 1 8 9 8 12 10 9 11 12 Lens Power input Connctor 12VDC/24VAC Dual Voltage (Vari-focal Only) Video Output Connector - BNC Service Monitor Output Connector Model #: CA-SMC30 (Vari-focal Only) Camera Power Board (Vari-focal Only) Safety Wire Bubble Dome Cover Camera Module Surface Mount Plate Assembly Screws Philips M3x12 (Indoor) Torx M4x11 (Vandalproof) Mounting Screws Philips ST4x30 (Indoor & Vandalproof) 7 11 Note: These assembly screws are l
Camera Dimensions EasyView™ Lite dome camera housing is specially designed allowing for additional 12° tilt of the 3-Axis Gimbal. Even at full 90° tilt, the view out of the EasyView™ Lite will be unobstructed. See the diagrams below for the exact dimensions of the EasyView™ Lite dome camera. Dimensions Unit: Inches (mm) R44,0 12˚ 3.54” (90) 2.09” (53) yY\ YU[_GO]ZP GG[T GG[U\Go \UX] OXZXP \UX] OXZXP YU[_GO]ZP 9
Base Installations 1. Remove the dome cover by loosening the 4 screws located at the Dome Cover Ring. EasyView™ Lite indoor domes use the standard philips screws, while vandal domes uses the torx screws. Use the Torx Wrench supplied. 2. Using four ST4x30 screws provided, mount the surface mount plate to a strudy surface. Using four M3x12(Indoor) screws, or M4x11(Vandalproof) screws, affix the dome cover back on to the surface mount plate.
Connecting to Monitors Follow the diagram below to make proper connections to the CRT Monitor or the Service Monitor. 12VDC/24VAC CCTV Monitor Service Monitor Output Service Monitor 30cm CA-SMC30 (Supplied with EasyView™ Lite dome) • Power connection (Auto polarity detection and protection) - 12VDC/24VAC Dual Voltage on Vari-focal Lens models, otherwise 12VDC Voltage for Fixed Lens models.
Adjusting the Vari-focal DC Auto Iris Lens Follow the instruction provided below to make any lens adjustments. Adjust the Focus Adjust the angle of Field of View Zoom: Tele A - D Wide Focus: Far A - D Near 1 2 3 4 5 12 Loosen the Zoom & Focus screws. Using the screw, move it LEFT or RIGHT to the desired position. Once the desired adjustments have been made, tighten the screw to lock in place.
Adjusting the 3-Axis Gimbal The Gimbal mechanism yields maximum rotation and placement as shown below.
Opening the 3-Axis Gimbal Cover Dip Switches on the EasyView™ Lite dome cameras are located on the camera module inside of the Gimbal assembly. To access the Dip Switches, remove the Gimbal cover temporarily by following the instructions below. STEP 1 Firmly hold the Gimbal base free of any movement. Press points A & B and pull the Gimbal cover off from the Gimbal base. STEP 2 Make the desired Dip Switch adjustments. STEP 3 Place the Gimbal cover back at the Gimbal base.
Switching OFF/ON the IR LEDs IR LED Dip Switch This Dip Switch is used to switch OFF/ON the IR LEDs. Too much IR reflection from a subject causes over-exposure on the most focused area causing ‘Hot Spots’ within the picture. Adjust this setting can help avoid such problems. • OFF: Select the OFF setting if the subject in the picture has extreme IR LED reflection. • ON: Select the ON setting if the subject in the picture has no IR LED reflection.
Dip Switch Functions and Operation Follow the instructions provided below to switch ON/OFF the various available camera functions and modes. DIP Switch Functions Function Dip Switch Each Dip Switch represents the various functions and modes. Switch On/Off the various functions and modes by following the Dip Switch position on the right.
Dip Switch Menu Control Terms A. ICR Filter Delay Timer (ICR Switch Time) This switch is used to delay the automatic ICR cut-filter. • ON: The automatic ICR cut-filter is delayed only by 2~3 seconds. • OFF: The automatic ICR cut-fllter is delayed by 4~5 seconds. B. FLK Mode This function is used to correct flickering of the screen when the camera is operating under certain fluorescent lighting. Flickering most commonly occurs if the fluorescent light uses a 50Hz power supply.
Technical Specifications | NTSC Technical Specifications Video Format Image Sensor Horizontal Resolution Day/Night Functionality Lens Type Angle of View Sync System Effective Pixels Scanning System Electronic Shutter Main Video Output Service Monitor Output Minimum Illumination S/N Ratio General Information Operating Temperature Operating Humidity Power Consumption Input Voltage CD-H2N NTSC/PAL 1/3” CCD 550 TV Lines No Fixed 2.9mm 120° Internal 768(H) x 494(V) 525 Lines.
Technical Specifications | NTSC Technical Specifications Video Format Image Sensor Horizontal Resolution Day/Night Functionality Lens Type Angle of View IR LED IR LED Distance LED Illumination Angle Sync System Effective Pixels Scanning System Electronic Shutter Main Video Output Service Monitor Output Minimum Illumination S/N Ratio General Information Operating Temperature Operating Humidity Power Consumption Input Voltage CD-HD2N-L CD-HD39N-L NTSC/PAL 1/3” CCD 550 TV Lines Yes Yes w/ ICR Fixed 2.
Technical Specifications | PAL Technical Specifications Video Format Image Sensor Horizontal Resolution Day/Night Functionality Lens Type Angle of View Sync System Effective Pixels Scanning System Electronic Shutter Main Video Output Service Monitor Output Minimum Illumination S/N Ratio General Information Operating Temperature Operating Humidity Power Consumption Input Voltage CD-H2P NTSC/PAL 1/3” CCD 550 TV Lines No Fixed 2.9mm 120° Internal 752(H) x 582(V) 625 Lines. 2:1 Interlaced 1/50 ~ 1/100,000 sec.
Technical Specifications | PAL Technical Specifications Video Format Image Sensor Horizontal Resolution Day/Night Functionality Lens Type Angle of View IR LED IR LED Distance LED Illumination Angle Sync System Effective Pixels Scanning System Electronic Shutter Main Video Output Service Monitor Output Minimum Illumination S/N Ratio General Information Operating Temperature Operating Humidity Power Consumption Input Voltage CD-HD2P-L CD-HD39P-L NTSC/PAL 1/3” CCD 550 TV Lines Yes Yes w/ ICR Fixed 2.
Memos & Notes 22
Memos & Notes 23
