Installation Manual

109
• Always depress the power button
when not in use. The blue light will
stop glowing, signifying the power
is o. With an internal thermal
breaker that shuts o the motor
base when the unit overheats. If
the motor base overheats and
shuts o, unplug the motor base
and press the power button,
located 90° to the left of the
G-Button and let it cool for an
hour or more before attempting to
use it again. motor base will reset
when the unit is powered o and
the thermal breaker has cooled
down suciently.
CLEANING SAFEGUARDS
• After making a smoothie or
souperblast, the blade must be
cleaned immediately.
• Always unplug motor base
and depress the power button
prior to cleaning, assembling or
disassembling.
• Never submerge the motor
base in water or place it in
the dishwasher. Wipe o any
debris inside the motor base
immediately to keep it in good
working order.
• Do not wash the blades in
the dishwasher as elevated
temperatures can damage gasket
seals.
• Do not remove the rubber liner
inside the motor base. To clean,
unplug first, then wipe with a
sponge moistened with warm
water.
• The NutriBullet
®
Rx cups can be
washed in the dishwasher and
should be washed on the top
rack of the dishwasher using the
normal (not sanitize) cycle.
• The NutriBullet
®
Rx cups and
blades should not be emmersed
in boiling water for any reason as
this will warp the plastic and
damage gaskets.
• Blades are sharp! Use care when
cleaning blades to avoid injury!
Rinse blades immediately after
each use to prevent debris from
drying and sticking to blade
components. If necessary, use
included brush to loosen any
debris around blades, gaskets
and blade housing threads
with care.
• Handwash only with mild dish
soap and warm water
(not hot).
• Dry immediately.
• For tough debris, fill the cup ½
full with room temperature (not
hot), mild soapy water. Then,
simply twist on the blade, pop it
on the base and give it a run for
30-45 seconds. Follow up with a
thorough brushing..
• When washing blades, do not
attempt to remove the gasket
ring. Simply hand wash the
blades in warm, mild soapy water.
Attempted removal of the gasket
may permanently damage the
blade configuration and cause
leakage. If in time a gasket
becomes loose or damaged,
please contact customer service
for a replacement NutriBullet
®
Rx
blade holder at:
1-800-523-5993.
STUBBORN CLEANUP
• If ingredients dry inside
the NutriBullet
®
Rx cups or
souperblast pitcher, make your
cleanup a snap by filling the
cup about 2/3 full with room
temperature soapy water and
screw on the extractor blade
and if using the souperblast
pitcher, put on lids. Place the
cup assembly on the NutriBullet
®
Rx motor base for about 20-30
seconds. This will loosen the stuck
ingredients, and with a light scrub
and rinse in warm water, you’ll be
all done.
CLEANING THE
NUTRIBULLET
®
RX
MOTOR BASE
HERE’S HOW TO
CLEAN IT UP
STEP 1:
The most important thing is to
UNPLUG the motor base before
cleaning
!
STEP 2:
Use a damp rag to wipe
down the inside and outside of
the motor base.
• NEVER SUBMERGE THE MOTOR
BASE IN WATER OR PLACE IT IN THE
DISHWASHER.
• Never put your hands or utensils
near the moving blade and never
use your hands or utensils to press
the activator buttons down while
the motor base is plugged in.
HEAVY CLEANING:
• Should the inside of the base
become sticky due to spillage
you may follow these
additional cleaning instructions:
• UNPLUG the motor base and
depress the power button
BEFORE cleaning.
• Place the motor base on a
dish towel to catch any liquid
or debris.
• Create a diluted vinegar and water
solution using 1 TBSP of vinegar
and 2 TBSPs of warm water. Pour
the solution into the motor base
where the blade assembly would
sit during normal use.
• Immediately use a dish brush to
dislodge any debris and wipe it out
with a damp cloth.
• The motor base is constructed
with a drain tube to drain any
liquid debris safely through to the
dish towel without damaging the
inside components.
Save these
instructions!
If you have any comments, questions,
or concerns, please go to
nutribullet.com.
Or call customer service at:
1-800-523-5993.
!