Installation Manual

87
will turn o and the blade will
stop spinning. To turn o machine
at any time during souperblast
mode (indicated by the orange
glowing G-Button), press the
power o button, located 90˚ to
the left side of the G-Button and
simply lift the souperblast pitcher
o the motor base. When the
vessel is removed from the motor
base, only the orange G-Button
light will turn o. When the power
o button is pressed, the blue light
will turn o and the blade will stop
spinning. Always press the power
o button when machine is not
in use.
SAFETY WARNINGS FOR
EXTRACTING FOR SOUP
Warning!: Only use the
vented souperblast pitcher
and two-piece lid
while operating the
NutriBullet
®
Rx in
souperblast mode. The
souperblast pitcher is
specially vented to release
pressure as the soup
mixture heats. Other
vessels are unvented and
may rupture and cause
personal injury if misused in
souperblast mode.
• To prevent overheating: do not
repeat souperblast mode for
the same hot soup. If more heat
is required, place the contents
in a microwave-safe container
and continue heating to desired
temperature. To make a new
soup, empty old contents, add
new ingredients and wait 1 full
minute before returning the vessel
to the motor base to start a new
smart technology cycle. Do not
repeat more than 2 cycles in
souperblast mode resting 1 minute
between cycles.
• Do not run the NutriBullet
®
Rx in
souperblast mode for more than
2 cycles consecutively without
allowing the NutriBullet
®
Rx motor
base and souperblast accessories
cool o for 30-60 min. To prevent
overheating and allow ingredients
to settle before continuing to
blend.
• If motor base does not shut o
after one (1) 7-minute interval
during souperblast mode, depress
the power button, located 90° to
the left side of the G-Button or
simply lift the souperblast pitcher
o of the motor base.
• Allow motor base to shut o
completely after initial interval
and wait for 3-4 minutes between
intervals.
• Motor base is equipped with an
internal thermal breaker that
shuts o the motor base when the
unit overheats. If the motor base
overheats and shuts o, unplug
the motor base or press the power
button, located 90° to the left of
the G-Button and let it cool for an
hour or more before attempting to
use it again. Motor base will reset
when the unit is powered o and
the thermal breaker has cooled
down suciently.
HEAT CAUTIONS
• During souperblast mode, the
contents inside can reach up to
about 70°C / 150°F through the
friction of the rotating blade.
• Keep hands and other exposed
skin away from the lid opening
to prevent possible burns during
souperblast mode.
• Do not remove the lid during
processing of soup—ingredients
will become hot and may splash
out and cause injury.
• Do not touch souperblast
pitcher directly with hands
after souperblast mode! The
souperblast pitcher surface,
blades and coupling gear will
be hot!
• Always use appropriate heat
resistant pads on the handle
to hold the souperblast pitcher
and to support the bottom of the
container.
• Carefully open souperblast
pitcher lid after souperblast mode,
as escaping steam and moisture
may cause scalding burns.
• Always attach blade to
souperblast pitcher and
hand tighten or use the blade
remover to tighten the blade to
prevent leakage prior to adding
ingredients into the pitcher.
• Never use the extractor blade to
blend without liquid as doing so
may damage the blade or motor.
• Do not use the souperblast
pitcher on the motor base without
the black lid and clear vent
top in place when running the
NutriBullet
®
Rx.
• To turn the NutriBullet
®
Rx on in
souperblast mode using smart
technology, plug the motor base
into an electrical outlet. Press
the power button, located 90˚
to the left side of the G-Button.
The power button will glow
blue, signifying the power is on.
Next, place the cup blade-side-
down onto the motor base. This
will activate the NutriBullet
®
Rx’s smart technology function,
causing the G-Button at the front
of the unit to glow green.
• Press the green G-Button down
for 2 seconds until it glows orange.
This will indicate that souperblast
mode has begun. The unit will run
in souperblast mode for about
7 minutes before automatically
turning o. Once o, simply lift
the souperblast pitcher o of the
motor base.
• The motor will run 3 cycles during
the 7 minute program—it will slow
down twice through the cycle to
allow the ingredients to settle for
improved processing then it will
increase again for the next part of
the cycle. This is a normal function
of the NutriBullet
®
Rx.
• The contents inside can reach up
to about 70°C / 150°F through the
friction of the rotating blade.
• If you wish to process your soup
for less than the programmed
time, you may simply lift o the
souperblast pitcher or press the
power button, located 90˚ to the
left side of the G-Button.
• Always allow it to come to a
complete stop prior to adding
additional ingredients during the
processing period.