Installation Manual

65
• NEVER PUT THE EXTRACTOR
BLADE ON THE MOTOR BASE
WITHOUT BEING SECURELY
ASSEMBLED ONTO CUP FIRST.
• Always operate pitcher with
vented cover in place.
• Keep hands and utensils away
from the cutting blade while
chopping or blending food to
reduce the risk of severe personal
injury or damage to the device.
A scraper may be used, but only
when the blender is not running.
• To reduce the risk of injury, make
sure the blade base is securely
screwed onto the cup before
placing it on the motor base and
operating the appliance.
• Do not use NutriBullet
®
Rx
outdoors.
• Do not blend hot liquids in sealed
oversized or short NutriBullet
®
cups.
EXTRACTING SMOOTHIES
NutriBullet
®
Rx IS
PROGRAMMED TO RUN
FOR 1 MINUTE DURING
SMOOTHIE MODE
(G-BUTTON WILL BE
GREEN).
• If motor base does not shut o
after 1 minute during smoothie
cycle, stop it manually by
depressing the blue illuminated
power button, located 90˚ to the
left side of the G-Button or simply
lift cup o motor base.
• To turn o the machine at
anytime during the smoothie cycle
(G-Button will be green), depress
the power button, located 90˚ to
the left side of the G-Button or
simply lift the cup o the motor
base. If you press the G-Button
for 2 seconds during extraction
and the light turns orange, you
are in souperblaster mode.
WARNING: Never use sealed cups
in souperlaster mode! Depress
the power button, located 90˚ to
the left side of the G-Button and
simply lift the cup o the motor
base to turn o the unit. The
light will stop glowing, signifying
power is o. Always unplug the
motor base upon completion of
processing.
• Do not touch coupling gear
directly with hands after smoothie
mode! The coupling gear in blade
base and motor base will be hot!
• Do not run in smoothie mode for
more than 1 interval.
• After initial cycle, allow motor
base to shut o completely and
wait for 15 seconds before starting
another cycle.
• Do not run for more than 3
consecutive 1 minute intervals
without allowing motor base to
cool to prevent overheating and
allow ingredients to settle for
2-3 minutes after the 3rd
extraction cycle.
• Motor base is equipped with an
internal thermal breaker that
shuts o the motor base if the
unit overheats.
• If the motor base overheats and
shuts o, unplug the motor base
and press the blue illuminated
power button, located 90˚ to the
left of the G-Button and let it
cool for an hour or more before
attempting to use it again. Motor
base will reset when the unit is
powered o and the thermal
breaker has cooled down
suciently.
• When making nut butters or
oil-based foods, due to the
consistency, the food will process
and then stick to the sides of the
pitcher. Process in 30 second
increments only by simply lifting
the pitcher o the motor base
between intervals. Between
cycles, open pitcher as needed to
scrape down the ingredients to
the center of the pitcher before
continuing to process in 30 second
increments.
• Allow machine to cool down for
10 min after 4-5 cycles to prevent
overheating and damaging
the unit.
• To prevent leakage, always align
and hand-tighten or use blade
remover to tighten the blade
to the NutriBullet
®
Rx cup prior
to inverting it and placing the
assembly on to the motor base.
• To turn on the NutriBullet
®
: plug
the motor base into an electrical
outlet. Press the power button,
located 90˚ to the left side of
the G-Button. This will cause
the power button glow blue.
Next, place the cup blade-side-
down onto the motor base. This
will activate the NutriBullet
®
Rx’s smart technology function,
causing the G-Button at the front
of the unit to glow green.
• Once activated, the unit will run
for 1 minute in regular smoothie
mode before it automatically
turns o. The G-Button will
stop glowing green at the end
of the 1-minute cycle. To turn
o completely before the cycle
is complete, either lift the cup
o of the base, or press the
power button, located 90° to the
left side of the G-Button. The
power button will extend from its
recessed position and the blue
light will no longer be lit, signifying
the power is o.
• In smoothie mode, the motor will
run 2 cycles during the 1 minute
interval— first it will slow down
half way through the 1 minute
interval to allow the ingredients
to settle for improved processing,
then it will power-up again for
the second half of the interval.
This is a normal function of the
NutriBullet
®
Rx.
• Turn the NutriBullet
®
Rx o after
each use. Depress the power
button, located 90˚ to the left side
of the G-Button. The blue light will
stop glowing, signifying power
is o.
POWER OFF
INSTRUCTIONS
• To turn o the machine at
anytime during the smoothie cycle
(indicated by the green glowing
G-Button), depress the power
button, located 90° to the left side
of the G-Button and simply lift
the cup o motor base. When the
vessel is removed from the motor
base, only the green G-Button
light will turn o. When the power
o button is pressed, the blue light