Model NP629004 ENGLISH........................................2 FRANÇAIS...................................11 ESPAÑOL....................................20 Broan-NuTone LLC. 926 West State Street, Hartford, WI 53027 NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 REGISTER YOUR PRODUCT ONLINE AT www.nutone.
READ AND SAVE THESE INSTRUCTIONS ! INTENDED FOR DOMESTIC COOKING ONLY ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being switched on accidentally.
! CAUTION 1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 2. Take care when using cleaning agents or detergents. 3. Avoid using food products that produce flames under the Range Hood. 4. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 5.
PREPARE THE HOOD Unpack hood and check contents.
INSTALL THE DUCTWORK ROOF CAP NOTE: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. 4. Install a roof or wall cap. Connect 6" round metal ductwork to cap and work back towards hood location.
WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. 1. Remove the wiring box cover. Remove a knockout from the wiring box. 2. Secure the conduit to the wiring box through a conduit connector. 3. Make electrical connections. Connect white to white, black to black and green to green. 4. Replace wiring box cover and screws.
INSTALL DECORATIVE FLUE SWITCH CABLE 1. Hold the decorative flue near the top of the hood. Connect the switch cable from the hood to the decorative flue, as shown. 2. Slide the lower decorative flue section downward and into the channels on the hood. CHANNEL LOWER DECORATIVE FLUE SECTION CHANNEL 3. Raise upper decorative flue section and attach it to the flue mounting bracket with screws (supplied) - 3.9x9.5mm. UPPER DECORATIVE FLUE SECTION FASTEN TO FLUE MOUNTING BRACKET WITH SCREWS (3.9x9.
MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. Grease Filter Clean the grease filter frequently. Remove the grease filter by pulling it downward. Use a warm detergent solution. Grease filters are dishwasher safe. After cleaning the grease filter, remount as follows: 1.Remove the halogen lamps. 2.Remount the grease filter. 3.Remount the halogen lamps. Interior Hood Cleaning DISCONNECT POWER TO HOOD BEFORE CLEANING! 1. Remove the grease filter as shown above. 2.
OPERATION Controls The hood is operated using the (7) pushbuttons located at eye-level, on the front of the decorative flue. LIGHT BLOWER BLOWER RESET SPEED SWITCH SPEED LOWER HIGHEST BLOWER BLOWER TIMED The light switch turns the halogen lights on ON-OFF SPEED SHUTand off. Push the light switch once to turn the SWITCH HIGHER OFF lights ON - push a second time to turn the lights ON to a brighter level - push a third time to turn the lights OFF.
HALOGEN BULBS This range hood requires two halogen bulbs (Type MR16, 12V, 20W). To change bulbs: 1. Remove the grease filter. 2. Remove bulbs by pulling them straight downward. Do not rotate bulbs. 3. Remount the grease filter. 4. Replace bulbs by aligning the bulb’s pins with the receptacle holes and pushing bulb upward. FUSE REPLACEMENT FUSE SWITCH OFF THE ELECTRICITY SUPPLY. Push the lower flue upwards. Open the electrical box. Replace with the same type of fuse (5x20mm, 4A, 125V).
LISEZ ET CONSERVEZ CES INSTRUCTIONS ! SEULEMENT POUR UTILISATION DOMESTIQUE ! AVERTISSEMENTS POUR REDUIRE LES RISQUES D’INCENDIE, DE DECHARGES ELECTRIQUES OU DE DOMMAGES AUX PERSONNES, OBSERVEZ LES INSTRUCTIONS SUIVANTES: 1. N’utilisez cet appareil que comme cela est indiqué par le constructeur. Si vous avez des problèmes, contactez le fabriquant à l’adresse ou au numéro de téléphone indiqués dans la garantie. 2.
4. Utilisez un extincteur SEULEMENT si: A. Vous savez que vous avez un extincteur Classe ABC, et vous en connaissez déjà le mode d’emploi. B. Ce n’est pas un très gros incendie et qu’il se limite à l’endroi où il a explosé. C. Vous êtes en train d’avertir les pompiers. D. Vous avez la possibilité d’essayer d’éteindre l’incendie en ayant le dos tourné vers une issue. * D’après les “Suggestions concernant la Sécurité contre les incendies des cuisines” publiées par NFPA. ! ATTENTION 1.
PREPAREZ LA HOTTE Enlever la hotte dans l’emballage et controller le contenu.
INSTALLATION DU SYSTEME D’EVACUATION COUVERCLE DU TOIT TUYAU ROND DE 6” REMARQUE: Pour réduire les risques d’incendie, n’utilisez que des tuyaux en métal. 1. Décidez où le tuyau doit être installé, entre votre hotte et l’extérieur. 2. Un tuyau droit et court permettra à votre hotte de fonctionner d’une façon plus efficace. 3. Un tuyau long avec des coudes et des transitions réduira le bon fonctionnement de votre hotte. En utiliser le moins possible. 4. Installez un couvercle sur le toit ou au mur.
INSTALLATION ELECTRIQUE Remarque: Ce modèle de hotte doit être relié à la terre correctement. Cet article devrait être installé par un électricien qualifié selon les lois nationales et locales en matière d’électricité. 1. Enlevez le couvercle de la boîte de connexion électrique. Ouvrez un trou de la boîte de connexion électrique. 2. Fixer le “conduit” au boîtier de connexion à l’aide d’un connecteur approprié pour ce “conduit”. 3. Faites le raccordement électrique.
INSTALLATION DU CONDUIT DECORATIF CÂBLE DES COMMANDES 1. Tenez le conduit décoratif près du haut de votre hotte. Reliez le câble des commandes de votre hotte au conduit décoratif, comme cela est indiqué. 2. Faites glisser la section du bas de votre conduit décoratif vers le bas, dans les rainures de votre hotte. RAINURE SECTION DU BAS DE VOTRE CONDUIT DECORATIF RAINURE 3.
ENTRETIEN Un bon entretien de votre hotte garantira une excellente performance. Filtre anti-graisse Nettoyez le filtre anti-graisse fréquemment. Enlevez le filtre anti-graisse en le tirant vers le bas. Utilisez une solution détergente tiède. Les filtres anti-graisse peuvent être lavés au lavevaisselle. Une fois le filtre anti-graisse nettoyé, procéder comme suit pour son remontage: 1.Retirer les ampoules halogènes. 2.Remonter le filtre anti-graisse. 3.Remettre en place les ampoules halogènes.
Les surfaces peintes doivent être nettoyées avec de l’eau tiède additionnée d’un détergent doux seulement. Nettoyage du verre Utilisez seulement un chiffon doux et un produit nettoyant pour le verre! N’UTILISEZ PAS d’éponges abrasives, de laine d’acier ou de produits dégraissants N’UTILISEZ PAS de solutions nettoyantes fortes ni de poudres abrasives. FONCTIONNEMENT LUMIERE VITESSE MAX.
AMPOULES HALOGENES Ce modèle de hotte a deux ampoules halogènes (Type MR16, 12V, 20W) Pour changer les ampoules: 1. Enlever le filtre anti-graisse 2. Enlever les ampoules en les tirant tout droit vers le bas. Ne pas faire tourner les ampoules. 3. Remonter le filtre anti-graisse. 4. Remettre les ampoules en alignant les fiches des ampoules avec les cavités à l’intérieur desquelles elles doivent être insérées et en poussant les ampoules vers le haut. REMPLACEMENT FUSIBLE FUSIBLE DÉBRANCHEZ L’APPAREIL.
LEA Y CONSERVE ESTAS INSTRUCCIONES ! INDICADO PARA EL USO EN COCINAS DOMESTICAS ! ADVERTENCIA PARA EVITAR EL RIESGO DE INCENDIO, CORTOCIRCUITO O DAÑO PARA LAS PERSONAS, OBSERVE ATENTAMENTE LAS SIGUIENTES NORMAS: 1. Use esta unidad solamente de la manera indicada por el fabricante; si tiene dudas, póngase en contacto con éste a la dirección o teléfono indicados en la garantía. 2. Antes de hacer una revisión o de limpiar la unidad, desconéctela de la red para evitar que se encienda de manera accidental.
! ADVERTENCIA 1. Para reducir el riesgo de incendios y para evacuar correctamente los humos, asegurarse de haber realizado una conducción del aire hasta el exterior. No expulsar los humos en espacios cerrados por paredes o techos, áticos, espacios angostos o garajes. 2. Prestar la máxima atención al utilizar productos de limpieza o detergentes. 3. Evitar el uso de productos alimentarios que puedan inflamarse bajo la campana. 4. Sólo para ventilación total.
PREPARE LA CAMPANA Sacar la campana de l’embalaje y controlar el contenido.
INSTALACION DEL TUBO DE EXTRACCION NOTA: para evitar el riesgo de incendio, use solamente material de metal. 1. Decida donde va a colocar el tubo de extracción entre la campana y la parte exterior. 2. Un recorrido de tubo corto y recto permitirá a la campana funcionar de manera más eficaz. 3. Los recorridos largos de tubo, codos y manguitos impiden el buen funcionamiento de la campana. Use el menor número de ellos posible. 4. Instale una cubierta ó una tapa.
INSTALACION ELECTRICA Nota: Este tipo de campana tiene que ser conectada a tierra cuidadosamente. La unidad debe instalarla un técnico electricista siguiendo las normas nacionales y locales. TAPA DE CONEXIÓN ELÉCTRICA 1. Quite la tapa de la caja de conexión eléctrica y saque un cable. 2. Fije el “conduit” a la caja de conexión por medio de un conector idóneo para el “conduit”. 3. Haga las conexiones eléctricas, una blanco con blanco, negro con negro y verde con verde. 4.
INSTALACION DEL TUBO DECORATIVO CABLE DE MANDOS 1. Mantenga el tubo decorativo cerca de la parte superior de la campana. Enchufe el cable de mandos de la campana al tubo decorativo como se indica. 2. Deslice la parte inferior del tubo decorativo hacia abajo e introdúzcala en los conductos de la campana. CONDUCTOS PARTE INFERIOR DEL TUBO DECORATIVO CONDUCTOS 3. Suba la parte superior del tubo decorativo y engánchela en el soporte para el montaje del tubo por medio de tornillos (adjuntos) 3.9x9.5mm.
MANTENIMIENTO Un mantenimiento adecuado de la campana asegura el funcionamiento correcto del aparato. Filtros antigrasa Limpie el filtro antigrasa con frecuencia. Tire de él hacia abajo para extraerlo y limpiarlo. Use un detergente que no sea fuerte. Los filtros antigrasa se pueden meter en el lavavajillas. Una vez limpiado el filtro anti-grasa, proceda de la siguiente manera para volver a montarlo: 1. Quite las lámparas halógenas. 2. Monte el filtro anti-grasa. 3. Monte las lámparas halógenas.
Limpieza del cristal Use un paño suave y un producto limpiacristales solamente No use paños fuertes, esponjas de acero o estropajos. No use productos de limpieza fuertes o abrasivos. FUNCIONAMIENTO LUZ VELOCIDAD MÍNIMA VELOCIDAD TURBO RESET Mandos La campana se pone en funcionamiento utilizando los (7) mandos situados a la altura de los ojos en la parte delantera del tubo decorativo.
LAMPARAS HALOGENAS Este tipo de campana necesita dos lámparas halógenas (Tipo MR16, 12V, 20W). Para cambiar las lámparas: 1. Extraiga el filtro antigrasa. 2. Extraiga las lámparas tirando de ellas hacia abajo. No trate de sacarlas a rosca. 3. Monte el filtro anti-grasa. 4. Coloque las lámparas metiendo las clavijas de éstas en los agujeros y empujando las lámparas hacia arriba. SUSTITUCION FUSIBLE FUSIBLE DESCONECTAR EL APARATO. Empúje el tubo decorativo hacia arriba.
SERVICE PARTS NP62000 SERIES RANGE HOOD - Parts for stainless steel models shown. For service parts for black or white models, call Broan Customer Service. KEY NO. PART NO.
LISTE PIECES DE RECHANGE NP62000 SERIES RANGE HOOD - Ci-dessous liste pièces de rechange pour hottes en inox. Pour les pièces de rechange des modèles de couleurs noir ou blanc, contacter Broan Customer Service. N. PART N.
LISTA DE PIEZAS DE RECAMBIO NP62000 SERIES RANGE HOOD - Aquí aparecen solamente las piezas de recambio para campanas de acero inoxidable, si desean las piezas de recambio de los modelos en blanco ó negro, pónganse en contacto con el servicio al cliente de Broan. CÓD. N. PIEZA N.
SERVICE PARTS - LISTE PIECES DE RECHANGE LISTA DE PIEZAS DE RECAMBIO NP62000 SERIES RANGE HOOD 04307653/1N