INSTALLATION INSTRUCTIONS HB0026 NP60000 SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL TO HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGE 11. NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687) www.nutone.com V7450 rev.
! WARNING ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 1. 2.
TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. SELECT BLOWER OPTION AND INSTALL DUCTWORK............................................................................6 MEASURE INSTALLATION...................................................................................................................7 PREPARE THE INSTALLATION .............................................................................................................7 INSTALL BACKSPLASH .......................
- NP60000 SERIES RANGE HOOD SYSTEM INTERIOR BLOWERS Model 437 (High capacity roof cap) Model 441 (10’’ round wall cap) Model 410 (10” round duct—2 ft. sections) Model 423 Model 424 (4 1/2” x 18 1/2” to (4 1/2” x 18 1/2” to 10” round - vertical 10” round - horiz. front/rear Model 634 or 644 (roof cap) Model 415 (7” round adjustable elbow) Model 418 (10” round adjustable elbow) Model 427 (4 1/2” x 18 1/2” to 10” round, 6” high - lateral Model 647 (7” round wall cap) Model 407 (7” round duct—2 ft.
- NP60000 SERIES RANGE HOOD SYSTEM IN-LINE AND EXTERIOR BLOWERS Model 437 (High capacity roof cap) Model 441 Model HLB9 (800 cfm) (10” round wall cap) Model 335 (1200 cfm) or HLB11 (1100 cfm) or 336 (1500 cfm) in-line blower Model 331H (600 cfm) exterior blower (includes two 8” x 12” to or 332H (900 cfm) 10’’ round transitions) exterior blower Model 441 (10” Round wall cap) Model HLB6 (600 cfm) in-line blower (includes two 4 ½” x 18 ½” to 10’’ round transitions) Model HLB3 (280 cfm) in-line blower (inc
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK Either an interior or exterior blower or in-line blower may be used with this hood. The NuTone Premier 60000 Series must be installed with blower models RM325H, RM326H, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately). NOTE: In addition to the blower models listed above, this hood is also compatible with older internal versions 325H and 326H.
2. MEASURE INSTALLATION Dimensions for the most common installation are shown below. The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities. Distances over 30” are at the installer and users discretion. Standard 8 ft. (2.
4. INSTALL BACKSPLASH (OPTIONAL) (Optional) RMP Series Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting screws. In order to be able to install the backsplash, make sure you have at least 18’’ clearance between bottom of hood and range control panel or cooktop. (See instructions packed with backsplash.) 5.
. INSTALL THE ROUGH-IN PLATE TO THE HOOD (ALL BLOWERS) Run power cable to installation location. Refer to the instructions included with the selected blower or rough-in kit (sold separately) for details on installing the rough-in plate. Install the rough-in plate so that the wiring box is located on the right side as you are facing the hood. For ducting through back of hood, remove existing plate from inside back of hood and attach it to inside top of hood to cover hole.
13. INSTALL LIGHT BULBS AND WARMING LAMPS Install (2) heat lamp bulbs. Use BR40 size, 250 W max., infrared bulbs only (sold separately). Install (3) halogen light bulbs. Use PAR20 size, 50 W (sold separately). 14. INSTALL FILTERS CAUTION Remove protective plastic film covering filters before installing them. It is recommended to install side filters first and finish with center one(s). 1. 2. 3. 4. Insert upper end of filter into the hood (finger sized cup side). Raise lower end toward the inside of hood.
15. USE AND CARE 16. OPERATION Grease Filters The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe. Wash more often if your cooking style generates greater grease—like frying foods or wok cooking. Remove filters by pushing filters towards the back of hood and rotating filters downward. Blower Cleaning Remove the filters in order to access the blower. Vacuum blower to clean. Do not immerse in water.
17. SERVICE PARTS 19 20 18 16 17 10 13 11 3 21 15 2 19 5 12 4 7 14 6 6 1 HL0031 8 9 1 KEY PART NO.
