Installation Guide

ManualsBrandsNuTone ManualsBathDecorative Brushed Nickel 80 CFM Ceiling Bathroom Exhaust Fan with Round Globe and Easy Change Trim

MODELS 770RLTK, 770RLTKC, 770RNLTK

ister. For Warranty Statement, or to order Service Parts: go to www.broan.

com and type the Model in the “Model Search” ﬁeld at the top of the page.

Broan, 926 W. State Street, Hartford, WI 53027 800-558-1711 or

888-336-3948

Ventilation Fan with Decorative Light

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PER-

SONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you

have questions, contact the manufacturer at the address or telephone

number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from be-

ing switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-rated construction codes and standards.

4. Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to prevent

backdrafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not install in a bathtub or shower enclosure.

8. This unit must be grounded.

9. This unit is U.L. listed. Type I.C. inherently protected.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors.

2. This product is designed for installation in FLAT CEILINGS ONLY. Do

not mount this product in a wall.

3. The light ﬁxture assembly must be mounted to the fan housing assembly

included with this product. Do not mount the light ﬁxture assembly to

a wiring outlet box.

4. To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

5. Please read speciﬁcation label on product for further information and

requirements.

TYPICAL INSTALLATIONS

HOUSING MOUNTED

DIRECTLY TO JOIST

2x6 (or larger)

Discharge parallel to joists.

HOUSING

2 x 4

CEILING

JOIST or

TRUSS

MOUNTING

TABS

POWER CABLE

ADDITIONAL

FRAMING

2 x 4

CEILING

JOIST or

TRUSS

CEILING

MATERIAL

GRILLE

PAN

GLASS

LIGHT SHADE

HOUSING MOUNTED

TO 2x4 TRUSS

Requires additional framing

for mounting tabs.

Discharge parallel to joists.

HOUSING MOUNTED

TO “I” JOIST

Requires additional framing

for mounting tabs.

Discharge parallel to joists.

Additional framing must be a 2x6 (minimum height).

SUSPENDED CEILINGS

Housing hung with wires -

3-point mount.

PLAN THE INSTALLATION

ROOF CAP*

(with built-in

damper)

WALL CAP*

(with built-in

damper)

4-IN. ROUND

ELBOWS*

4-IN. ROUND

DUCT*

FAN

HOUSING

Seal gaps

around

housing.

Seal duct

joints with

tape.

Keep duct

runs short.

INSULATION

(Place around and

over fan housing.)

POWER

CABLE*

*Purchase

separately.

INSTALL THE HOUSING

1. Choose the location for your fan in the ceiling. For best possible

performance, use the shortest possible duct run and a minimum

number of elbows.

2. Position mounting brackets

against joist so that bottom

edge of housing will be ﬂush

with ﬁnished ceiling.

Additional positioning

feature for 5/8”, 1”, &

1-1/4” thick ceiling material:

Holes in corners of housing

are labeled with various ceiling

material thicknesses. Position

housing so bottom edge of joist is visible through a matched

set of holes. The housing is now in the proper position for that

ceiling material thickness.

Additional positioning feature for 1/2” thick ceiling material:

Bend two tabs, on side of housing,

outward. Lift housing until

tabs contact underside of joist.

Mark the keyhole slot on both mounting brackets.

New Construction

5/8

1-1/4

TAB

HOLES

BOTTOM EDGE OF JOIST

- PLEASE NOTE -

THE FOLLOWING INSTALLATION ILLUSTRATIONS SHOW 2 X 6

JOISTS. IF YOU HAVE A TRUSS OR “I”-JOIST INSTALLATION, MOUNT

THE VENTILATOR TO THE ADDITIONAL FRAMING IN THE SAME MAN-

NER. (Additional framing must be a 2x6 (minimum height).

Summary of content (12 pages)

PAGE 1
Ventilation Fan with Decorative Light MODELS 770RLTK, 770RLTKC, 770RNLTK Register this product at www.broan.com/register or www.nutone.com/register. For Warranty Statement, or to order Service Parts: go to www.broan. com and type the Model in the “Model Search” field at the top of the page. Broan, 926 W.
PAGE 2
INSTALL THE DUCTWORK New Construction FLUSH 3. Set housing aside and drive nails partially into joist at the top of both keyhole marks. NOTE: The duct connector has a counter-balanced damper flap. The flap will be “open” approx. 1” when duct connector is attached to housing. This design permits insulation to be in direct contact with fan/ light housing per UL (Underwriters Laboratories) standards.
PAGE 3
ATTACH THE GRILLE PAN AND GLASS SHADE USE AND CARE WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVICING THIS UNIT. MOTOR 1. Locate the grille MOUNTING pan over the PLATE GRILLE GRILLE fan housing and SCREW PAN connect the wiring ROD harness plug into white receptacle in the fan housing. WASHER 2. Insert rod through washer and GLASS SHADE through center hole of grille pan. 3. Thread rod onto grille 60 WATT MAX.
PAGE 4
Ventilateur luminaire décoratif Pour enregistrer le produit, se rendre à fr.broan.ca/register.asp ou à fr.nutone.ca/register.asp. Pour lire l’énoncé de garantie ou commander des pièces, se rendre à fr.broan.ca et saisir le numéro de modèle dans le champ Recherche d’un modèle au haut de la page. Broan, 926 W.
PAGE 5
INSTALLATION DES CONDUITS Nouveau bâtiment (suite) AFFLEURANT 3. Mettre le boîtier de côté et insérer partiellement les clous dans la solive sur le haut des deux marques des encoches. N.B. : Le raccord de conduit est doté d’un clapet à contrepoids qui s’ouvre d’environ 2,5 cm lorsque le raccord est fixé au boîtier. Cette configuration permet à l’isolant d’être en contact direct avec le boîtier du ventilateur luminaire conformément aux normes d’Underwriters Laboratories (UL).
PAGE 6
INSTALLATION DU CADRE DE GRILLE ET DE L’ABAT-JOUR UTILISATION ET ENTRETIEN AVERTISSEMENT : AVANT DE PROCÉDER À L’ENTRETIEN OU AU NETTOYAGE DE L’APPAREIL, COUPER LE COURANT AU PANNEAU D’ALIMENTATION ET EN VERROUILLER L’ACCÈS. PLAQUE DE 1. Placer le cadre de FIXATION grille sur le boîtier DU MOTEUR VIS DE LA et brancher le GRILLE CADRE DE câble sur la prise GRILLE TIGE blanche du boîtier. 2. Insérer la tige dans la rondelle RONDELLE et dans le trou ABAT-JOUR central du cadre. EN VERRE 3.
PAGE 7
Ventilador Decorativa con la luz Registre este producto en www.broan.com/register o www.nutone.com/ register. Para Declaración de garantía, o para pedir piezas de servicio: vaya a www.broan.com y escriba el modelo en el campo “Model Search” en la parte superior de la página. Broan, 926 W.
PAGE 8
Construcción nueva 4. Coloque la cubierta en la abertura de manera que su borde inferior quede al ras del cielo raso terminado. Clave la cubierta en la vigueta a través del orificio en forma de cerradura, en ambos lados. Para asegurar un montaje sin ruido, coloque otro clavo en el orificio superior de cada aleta de montaje. 3. Coloque la cubierta a un lado e introduzca parcialmente los clavos en la vigueta, en la parte superior de ambas marcas de los orificios en forma de cerradura.
PAGE 9
CONEXIÓN ELÉCTRICA NEGRO ROJO BLANCO TIERRA (desnudo) AZUL CONTROL DOBLE (se vende por separado) CAJA DEL CONMUTADOR USO Y CUIDADO ADVERTENCIA: DESCONECTE LA CORRIENTE ELECTRICA Y BLOQUEE EL TABLERO DE SERVICIO ANTES DE LIMPIAR OR REPARAR LA UNIDAD. RECEPTÁCULO BLANCO (LAMP.) RECEPTÁCULO NEGRO (VENT.) REEMPLAZO DEL FOCO Quite la pantalla de vidrio. Reemplace los bulbos como necesarios. Utilice el bulbo tipo de E26, 60 vatios máximo o de eficiencia energética equivalente. LAMP. VENT.
PAGE 10
PAGE 11
PAGE 12
1102078B