Operation Guide

4 Button / 1 Way Remote Start Systems
QUICK START OPERATION GUIDE
4 Button / 1 Way Remote Start Systems
QUICK START OPERATION GUIDE
REMOTE START FUNCTIONS
FUNCTION BUTTON(S) NOTE
Engine Start/Stop
x 2
Activation is programmable (contact installer). Take Over: Turn ignition key ‘ON’ (not start), press brake pedal
Run Time Extender
The system will restart the internal run timer.
Low Battery & Low/
Hi Temp Auto-Start
, ,
Auto-start will activate a max of once per 2 hours. See your installer or the full manual for threshold settings.
Remote Valet
, , +
This disables remote start and the security system. The status LED will turn on. Repeat this process or press valet
button once to exit valet mode. TIP: You can also enter valet mode by holding the valet button for 3 seconds!
FUNCTION VALET BUTTON NOTE
Pit Stop Mode Press 2x w/ Engine Running
This will leave the engine running for the programmed run time so you can take your keys with you to run errands.
XL Pit Stop Mode Press 6x w/ Engine Running
This will leave the engine running for 12 hours so you can safely leave the engine running for extended periods.
Ideal for commercial vehicles using strobes, refrigerators boxes, etc.
MANUAL TRANSMISSION RESERVATION MODE
This must be performed before you can remote start a manual transmission vehicle to ensure
the car is in neutral & maximum safety. Consult your installer for more information.
1) With the engine running by key, hold the brake pedal & place the transmission in neutral.
2) Apply the parking brake and release the brake pedal.
3) Send the remote start command via your remote. The remote start should engage
(not crank) and the status LED will begin flashing.
4) Take the ignition key out of the switch (the engine should stay running).
5) Exit the vehicle and lock your doors with the remote. The engine will turn off.
Status LEDValet / Programming Button
WINDOW-MOUNT ANTENNA/RECEIVER
AUXILIARY REMOTE FUNCTIONS
FUNCTION BUTTON(S) NOTE
+
CH3/AUX1 - Write function in rst column*
+
CH4/AUX2 - Write function in rst column*
+
CH5/AUX3 - Write function in rst column*
+
AUX4 - Write function in rst column*
REMOTE START ERRORS
CHIRPS/FLASHES VIOLATED ZONE
LED ON System in Valet mode
1 Hood opened
2 Brake pedal pressed
3 Bad tach signal or engine over-rev.
4 BLACK/WHITE wire lost ground
5 3D motion detected while cranking
6 Received engine stop command
7 Alarm was triggered
8 Run time expired
9 Low vehicle battery voltage detected
If the system fails to remote start or remote start stops
unexpectedly, it will give a long horn/siren chirp followed by a
series of short horn/siren chirps & light flashes. The short chirps/
light flashes indicate the cause of the failure.
TIP: If remote start won’t activate, the system may be in valet
mode (Status LED ON). Press the valet button once to exit.
PROGRAMMING REMOTES TO THE SYSTEM (UP TO 4)
BEFORE YOU BEGIN: Have all remotes for the system at hand.
1) Turn the ignition key “ON” (do not start).
2) Press the valet button 5 times within 5 seconds of step 1.
- The horn will briefly sound
3) Press & release the “lock” button on each transmitter one after the other.
- 1-button models, press the “start” button.
- The siren/horn will chirp once for each transmitter.
- NOTE: When the rst remote is learned all previous remotes are erased.
- NOTE: All other button functions will automatically be assigned.
4) Turn the ignition key “OFF”.
- NOTE: The system will exit at any time
after 10 seconds of no activity.
SCAN TO WATCH
HOW-TO VIDEO
32
*These special functions may not be available on your vehicle. Consult your installer.