User's Manual

Entering the Vehicle While it is Running via Remote Start
1. Unlock the vehicle doors using the remote keyless entry system. If the vehicle’s doors are unlocked manually
using the key, the vehicle’s security system will trigger (if the security system is armed prior to activating the
remote start system) and the vehicle’s engine will turn off. Inserting the ignition key into the ignition cylinder and
turning it to the “on” position or pressing the unlock button on the remote keyless entry transmitter will disarm the
security system.
2. Enter the vehicle.
3. The engine will shut down upon opening any vehicle door, trunk, hatch or rear gate of 5-door / wagon vehicles.
4. Insert the key into the ignition and turn to the start position to re-start the engine.
Remote Start Confi rmation Feature
Your remote start transmitter is equipped with a unique bidirectional confi rmation feature. This feature will allow
the transmitter’s backlit button to display system status provided the vehicle and transmitter fall within the system’s
operating range. Typical transmitter button fl ash sequences are outlined below.
Transmitter Flash & Beep Sequence Feature Description
Flash when button is pressed (no audible beep) Indicates that the system is transmitting an RF signal
1 fl ash & 1 beep following remote start activation (transmitter
button is pressed 2 times within 3 seconds)
Indicates that the transmitter has received remote start activation
confi rmation from the vehicle system.
2 fl ash & 2 beeps following remote start activation (transmitter
button is pressed 2 times within 3 seconds)
Indicates that the transmitter has received confi rmation of a
successful start of the vehicle system (vehicle now running)
1 fl ash every 5 seconds (no audible beep) Indicates that the vehicle is running via remote start. If the
transmitter is moved outside of the systems operating range, this
sequence will time out after the default 15 minute vehicle run
cycle.
3 fl ashes & 3 beeps Indicates that the vehicle’s engine has turned off due to remote
start system 15 minute time out, vehicle safety parameter or
normal shut down.
Selectable Run-Time
The system is preprogrammed to run for fi fteen (15) minutes before automatically stopping. The programmed run
period can be changed to alternate times using the following procedure.
1. Enter the vehicle and close all vehicle doors, trunk or rear gate.
2. Verify that the transmission shifter is in the “park” position.
3. Turn the ignition to the “on” then “off”, “on” then “off”, “on” then “off”, then
back “on” and leave on throughout the programming process.
(on/off ignition cycles must be completed within 8 seconds).
4. The system will honk the horn the number of times corresponding to the
current run time setting.
5. Open and close the driver’s door to advance to the next run time setting.
The system will honk the horn the number of times corresponding to the
new run time setting.
6. Run time selection mode will exit via turning the ignition key off or thirty
(30) seconds of inactivity. Upon exit the current run time selection will be
stored.
Compliance
This device complies with Part 15 of the FCC rules and with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may cause undesired
operation.
Note: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment and void warranty.
To comply with RF exposure limits for general population/uncontrolled exposure, the antenna(e) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be
collocated or operating in conjunction with any other antenna or transmitter.
This radio transmitter has been approved by Industry Canada to operate with the antenna listed below. Antenna types
not included below or having a gain greater than that indicated below are strictly prohibited for use with this device.
Horn Honks Run Time
1 Three (3) Minutes
2 Five (5) Minutes
3 Ten (10) Minutes
4 Fifteen (15) Minutes
(Default Setting)
Approved External Antenna: Omni-directional, 2.1 dBi gain, 902-928 MHz, antenna impedance is 50 ohms.