Use and Care Manual

07
06
●
FEATURES
●
●
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.
The tool may fire when it is first
connected to the air source. Always
connect the tool point away from
yourself and others.
WARNING:
!
OPERATION
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
WARNING:
!
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672
MODEL: SPNNRMODEL: SPNNR
FEATURES
SPECIFICATIONS
AIR CONSUMPTION: 3.61 SCFM with 100
fasteners per minute @ 90 psi
AIR INLET: 1/4 inch NPT
WEIGHT: 1.63 lb(0.74kg)
MAXIMUM PRESSURE: 115 psi
PRESSURE RANGE: 70 psi – 115 psi
FASTENER RANGE: 0.077’’ to 0.148’’
Keep the tool pointed away from yourself
and others when working. Failure to do
so could result in possible serious
personal injury.
WARNING:
!
360° ADJUSTABLEE XHAUST
Allows user to direct air away from face.
COMFORT-GRIP HANDLE
For increased comfort and control.
ERGONOMICALLY ENGINEERED BODY
Rugged and comfortable resulting in a light-
weight tool great for extended use.
SETTING THE AIR PRESSURE
The amount of air pressure required depends on
the size of the fasteners and the workpiece material.
Begin testing the power of drive by punching out a
test nail at the same type of workpiece material
used for the actual job.
Punch out a test fastener with the air pressure set at
90-95 psi. Raise or lower the air pressure to find the
lowest setting that will perform the job with
consistent results.
It may be possible to achieve the desired power
with air pressure adjustments alone.
FIRING THE TOOL (SINGLE MODE)
Connect the tool to the air source.
Grip the tool firmly to maintain control. Slide the
nose of the tool to the shaft of the fastener.
Squeeze the trigger to punch a nail.
MAINTENANCE
Any time inspection, maintenance, and
cleaning are done:
◆Disconnect the tool from the air source.
◆Empty the nose completely.
WARNING:
!
Each tool is packed with an anti-dust cap on the air
connector.
Keep the anti-dust cap cover the air connector
when the tool is not in use.
ANTI-DUST
Lubrication is required for best performance after
long periods of use. Oil for pneumatic fastening
tools is added through the air line connection and
will lubricate internal parts.
LUBRICATION
Disconnect the tool from the air source to add
the lubricant.
Turn the tool so the air inlet is facing up. Place 2
- 3 drops of pneumatic fastening tool oil into air
inlet. Do not use detergent oils, oil additives, or
other air-tool oils as these lubricants will cause
accelerated wear to the seals and bumpers in
the tool, resulting in poor tool performance and
frequent tool maintenance.
2.
1.
0.077’’-0.148’’
(9Ga.-14Ga.)
⒈
2.
3.
Slide the nose of the tool onto the shaft of the
nail and bending the nail until it is straight, then
fire the tool to punch out the fastener.
Punch out straight fasteners.
Punch out bent fasteners.
Slide the nose of the tool onto the shaft of the
fastener, then fire the tool to punch out the
fastener.
Note:
◆
◆
After adding oil, connect the tool to the air
source, run tool briefly. Wipe off any excess oil
from the cap exhaust.
3.
Lubricate tool only with specified lubricants.
CAUTION: