Use and Care Manual

FEATURES
SPECIFICATIONS
AIR CONSUMPTION: 12.85 SCFM with 100
fasteners per minute @ 90 psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY: 90 fasteners, 10-12 gauge
WEIGHT: 8.4lbs
MAXIMUM PRESSURE: 115 psi
PRESSURE RANGE: 70 psi – 115 psi
FASTENER LENGTH RANGE: 2 inch to 3-1/2 inch
07
OPERATION
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool
allows users to direct the exhaust according to
operator preference. To adjust the direction,
turn the exhaust cap in the desired direction.
Connect the tool to the air source.
Pull the pusher (A) back to the rear of
magazine. Insert strip of fasteners into the
notch upon the magazine(B). Be sure the
fasteners are pointed downward.
Press the latch(C) to release the pusher to
let it go back to move the fasteners up to
the driving mechanism. The pusher will
stop when it rests against the end of the
fastener.
LOADING FASTENERS
Pusher(A)
Notch upon the magazine(B)
06
●
●
●
●
UNPACKING
This tool has been shipped completely
assembled.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until
you have carefully inspected and
satisfactorily operated the tool.
If any parts are damaged or missing,
please call 1-888-669-5672.
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
WARNING:
Do not attempt to modify this tool or
create accessories not recommended
for use with this tool. Any such
alteration or modification is misuse and
could result in hazardous condition
leading to possible serious personal
injury.
Such precautionary measures reduce the risk
of injury to persons.
LOADINGTOOL
Do not load the tool with fasteners when
any one of the operating controls is
activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point the tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental
actuation may occur, possibly causing
injury.
●
●
●
●
!
Th e w arn in gs and p re caut ions
discussed above cannot cover all
possible conditions and situations that
may occur. It must be understood by
the user that common sense and
caution are factors which cannot be
built into this product, but must be
supplied by the user.
WARNING:
1.
2.
3.
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672
MODEL: SFR2890 MODEL: SFR2890
28º
Latch(C)
The tool may fire when it first connected is
to the air . Always connect the tool source
to the air source before loading fasteners
to prevent injury from unintended cycling.
Always make sure the tool's magazine is
empty at the beginning of each work
session, before connecting to an air
source.
Only use fasteners recommended by the
manufacturer for this tool. Use of
fasteners not recommended by the
manufacturer could lead to injury to
persons in the work area, or damage to
the tool.
FEATURES
360° ADJUSTABLE EXHAUST
Allows user to direct air away from face.
ONE PIECE DRIVER BLADE
For increased durability.
COMFORT-GRIP HANDLE
For increased comfort and control.
MAGNESIUM BODY
Light-weight tool great for extended use.
DUAL-MODE TRIGGER
Easily allows for single or sequential firing.
ADJUSTABLE DEPTH
Depth is easily adjustable for various
applications.
ANTI-DRY-FIRING DESIGN
Reduces damage on internal components.
NON-MARRING SAFETY CONTACT
Eliminates damage to working surface.
Keep the tool pointed away from yourself
and others when loading fasteners.
Failure to do so could result in serious
personal injury.
Never load fasteners with the workpiece
contact or trigger activated. Doing so
could result in serious personal injury.
Compatible with generic brands of 28 degree
wire (or paper) collated clipped head framing
nails.