Use and Care Manual

●
●
●
●
UNPACKING
This tool has been shipped completely
assembled.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure
no breakage or damage occurred during
shipping.
Do not discard the packing material until
you have carefully inspected and
satisfactorily operated the tool.
If any parts are damaged or missing,
please call 1-888-669-5672.
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result
in possible serious personal injury.
WARNING:
!
WARNING:
Do not attempt to modify this tool or
create accessories not recommended
for use with this tool. Any such
alteration or modification is misuse
and could result in hazardous
condition leading to possible serious
personal injury.
Such precautionary measures reduce the risk
of injury to persons.
LOADINGTOOL
Do not load the tool with fasteners
when any one of the operating controls
is activated.
Never place a hand or any part of body
in fastener discharge area of tool.
Never point the tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental
actuation may occur, possibly causing
injury.
●
●
●
●
!
The warnings and precautions
discussed above cannot cover all
possible conditions and situations that
may occur. It must be understood by
the user that common sense and
caution are factors which cannot be
built into this product, but must be
supplied by the user.
WARNING:
●
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672
FEATURES
●
●
360°ADJUSTABLE EXHAUST
Allows user to direct air away from face.
ONE PIECE DRIVE BLADE
For increased durability.
COMFORT-GRIP HANDLE
For increased comfort and control.
ERGONOMICALLY ENGINEERED
BODY
Rugged and Comfortable resulting in a
light-weight tool great for extended use.
WITH RELOAD INDICATOR
Remain nail is seeable.
ADJUSTABLE DEPTH
Depth is easily adjustable for various
applications.
NON-MARRING SAFETY CONTACT
Eliminates damage to working surfaces.
●
●
FEATURES
SPECIFICATIONS
AIR CONSUMPTION 3 6: . SCFM with 100
fasteners per minute @ 90 psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY: 80 fasteners, 16 gauge
WEIGHT: 2.8 lbs
MAXIMUM PRESSURE: 110 psi
PRESSURE RANGE: 70 psi – 110 psi
FASTENER LENGTH RANGE: 3/4 inch to 2 inch
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool
allows users to direct the exhaust according to
operator preference. To adjust the direction,
turn the exhaust cap in the desired direction.
OPERATION
Connect the tool to the air source.
Push down on the Latch Button(A). Pull
back on the Magazine Cover(B).
Insert a stick of fasteners into the Magazine
Rail(C). Make sure the pointed ends of the
fasteners are resting on the bottom ledge of
the magazine when loading. Make sure the
fasteners are not dirty or damaged.
Push the Magazine Cover(B) forward until
latch button pops up.
LOADING FASTENERS
Latch button(A)
1.
2.
3.
4.
O n l y u s e t h o s e f a s t e n e r s
recommended for use with this tool.
Fasteners not identified for use with
this tool by the tool manufacturer are
able to result in a risk of injury to
persons or tool damage when used in
this tool.
WARNING:
!
!
WARNING:
The tool may fire when it is first
connected to the air source. Always
connect the tool to the air source
before loading fasteners to prevent
injury from unintended cycling. Always
make sure the tool’s magazine is empty
at the beginning of each work session,
before connecting to an air source.
Keep the tool pointed away from
yourself and others when loading
fasteners. Failure to do so could result
in possible serious personal injury.
WARNING:
!
Never load fasteners with the
wor kpi ece contact or t rig ger
activated. Doing so could result in
possible serious personal injury.
WARNING:
!
MODEL: SFN50 MODEL: SFN50
19mm
3/4”
1”
1-1/4”
1-1/2”
1-3/4”
2”
25mm
32mm
38mm
45mm
50mm
0.118”(3mm)
16Ga.
0.063”
1.6mm
0.055”
1.4mm
Compatible with generic 16 gauge straight finish
nails.
Pull Open
Magazine
cover(B)
Magazine rail(C)
FIG. 6
Push
against
nose
●
●
●
1-3/8”
35mm
1-5/8”
40mm