Full Product Manual

07
06
FEATURES
●
●
●
●
OPERATION
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
WARNING:
!
UNPACKING
This tool has been shipped completely
assembled.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call 1-888-669-5672.
●
●
●
●
●
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
WARNING:
!
HTTP://WWWNUMAXTOOLSCOM 1-888-669-5672
..
HTTP://WWWNUMAXTOOLSCOM 1-888-669-5672
..
FEATURES
SPECIFICATIONS
AIR CONSUMPTION: 4.32 SCFM with 100
per minute @ 90 psifasteners
AIR INLET:
MAGAZINE CAPACITY:
WEIGHT:
MAXIMUM PRESSURE:
PRESSURE RANGE:
1/4 inch NPT
L Cleat: 100 pcs
Staple: 90 pcs
7.27 lbs
115 psi
70 psi 115 psi–
FASTENER SIZE RANGE:
MODEL: S50LSDH MODEL: S50LSDH
Compatible with Generic Brands of 15.5 Gauge
Staples & 16 Gauge L-Cleats.
(16 Ga. L Cleats)
7.2mm (9/32”)
38 mm
45 mm
50 mm
1-1/2”
1-3/4”
2”
(15.5 Ga. Staples)
12.7mm (1/2”)
38 mm
45 mm
50 mm
1-1/2”
1-3/4”
2”
ERGONOMICALLY DESIGNED HANDLE
NON-MARRING DESIGN
DURABLE CONSTRUCTION
MALLET WITH RUBBER HEAD
INCLUDED
For ease of operation and reduced fatigue.
Provides increased protection from marring
when working with a finished flooring surface.
Lightweight, high-strength aluminum body with
heat treated steel parts.
WOODED
The tool is shipped with the Arm part detached
from the main body part.
(A)
Set the Arm(A) against the Handle .
Wrench-tighten the Nuts(B) until the Arm(A) and
Handle (C) are secured and the Arm is locked
against Handle.
(A)
(C)
Follow these instructions to prepare the tool for use.
1.
2.
PREPARE THE TOOL
If any parts are missing, do not operate
this tool until the missing parts are
replaced. Before using this tool, make sure
the arm part and the main body part are
screwed together tightly. Failure to do so
could result in possible serious personal
injury.
WARNING:
!
Connect the tool to the air source.
Pull the pusher (D) back to the end of
magazine . Lock the pusher in place by using
the lock button(E) . (See figure 1 & 2)
Insert strip of L cleats into
. Up to 100 cleat nails can be loaded
into the magazine. Noted that , when loading
the L cleats, the side with the L head should be
in the left of the magazine. (See figure 3)
Press the lock button(E), allow the pusher (D)
to slide forward and engage the. The
pusher (D) will stop when it rests against the
end of . (See figure 4)
athe top of the
magazine
fasteners
the cleats
⒈
⒉
⒊
⒋
LOADING CLEAT NAILS
Nut (B)
Hex. Bolt
Handle (C)
Arm(A)
Prepared
Flooring Nailer
Pusher(D)
Slide Back
Figure 1
Lock Button(E)
Figure 2