HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 PRIME GLOBAL PRODUCTS, INC. MODEL: S50LSDH HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 PRIME GLOBAL PRODUCTS, INC. WARNING: Failure to follow warnings could result in DEATH OR SERIOUS INJURY. SAVE THIS MANUAL FOR FUTURE REFERENCE.
MODEL: S50LSDH MODEL: S50LSDH GENERAL SAFETY RULES P3 UNPACKING P6 FEATURES P6 OPERATION PREPARE THE TOOL P7 LOADING CLEAT NAILS P7 LOADING STAPLES P8 UNLOADING CLEAT NAILS AND STAPLES P8 CHANGING THE FOOT PLATE P9 SETTING THE AIR PRESSURE P10 OPERATING THE TOOL P10 CLEARING JAMS P11 MAINTENANCE P12 RECOMMENDED HOOKUP P13 TROUBLESHOOTING P14 WARRANTIES P15 ● In this manual, on the labels, packages and all other information provided with this tool.
MODEL: S50LSDH MODEL: S50LSDH enables better control of the tool in unexpected situations. Do not attach the hose or tool to your body. Attach the hose to the structure to reduce the risk of loss of balance if the hose shifts. Always assume that the tool contains fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Wash hands after handling.
MODEL: S50LSDH MODEL: S50LSDH OPERATION FEATURES ! WARNING: The warnings and precautions discussed above cannot cover all possible conditions and situations that may occur. It must be understood by the user that common sense and caution are factors which cannot be built into this product, but must be supplied by the user. SPECIFICATIONS The tool is shipped with the Arm (A) part detached from the main body part. Follow these instructions to prepare the tool for use. 1.
MODEL: S50LSDH MODEL: S50LSDH Figure 3 Figure 6 L Cleat until it is locked into lock button. ( See figure 8 & 9.) ⒊ Unload the cleat nails or staples from the magazine.(See figure 10 & 11.) Lock Button (E) Figure 11 Figure 8 Pusher(D) L Cleat Figure 4 L Cleat Figure 7 CHANGING THE FOOT PLATE Staple The tool is equipped with a factory pre-installed 3/4 in. foot plate (G), and an additional uninstalled 5/8 in. & 9/16 in. foot plate . To change the plate: Figure 9 Lock Button (E) 1.
MODEL: S50LSDH MODEL: S50LSDH Figure 12 ! WARNING: An improperly functioning tool must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece. Screws (F) Hammer cap (H) Correct Placement TONGUE & GROOVE FLOORING Foot plate (G) Hand grip (J) Incorrect Placement Lcleat Lcleat or or Staples Staples 7.Return the Drive Blade back to its original position.(See figure17) 8.Replace the Nose Cover (L) and Nose Bolts(K). (See figure18) 9.
MODEL: S50LSDH MODEL: S50LSDH MAINTENANCE Figure 16 CLEANING Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust , oil, grease, etc. ! WARNING: Jammed Fastener Any time inspection, maintenance, and cleaning are done: ◆Disconnect the tool from the air source. ◆Empty the magazine completely.
MODEL: S50LSDH MODEL: S50LSDH CAUTION: The air compressor must be able to maintain a minimum of 70 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. ! WARNING: Do not connect with an air compressor which can potentially exceed 200 psi. As tool may burst, possibly causing injury.
