User’s guide « FCC » DECLARATION OF CONFORMITY FCC rules - PART 15 NUM’AXES declares that the training collar CANICOM 200 complies to all dispositions of the part 15 of the FCC rules This device complies with part 15 of the FCC. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interferences that may cause undesired operation.
WARNING Any person with individual device for cardiac assistance (pacemaker, defibrillator) must take precautions when they use CANICOM 200. This device emits some static magnetic fields (a magnet is located in the remote control). (Frequency= 915 MHz, at = 0.75 mW). The device complies with Part 15 of the FCC rules. Any technical changes or modifications on the receiver collar or on the remote control not expressly approved by the manufacturer shall void the user’s authority to operate the equipment.
Index ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Page Contents of the product ............................................................................................... 4 Description of the product ............................................................................................ 4 First use from new ...................................................................................................... 4 How to use the remote control ...........................................................
● Contents of the product Inside the packaging you will find: ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ 1 receiver collar CANICOM fitted with short contact points 1 lithium 3 Volts CR2 battery for the collar 1 remote control CANICOM 200 fitted with 1 lithium 3 Volts CR2430 battery 1 neon test lamp 1 pair of long contact points 1 carry strap 1 DVD This user’s guide ● Description of the product On/Off switch Continuous stimulations limited to 8 seconds Flash stimulations lower than 1 second 2 contact points (short or long) LCD sc
▪ ▪ If you do not hear any beep after having inserted the battery, remove it immediately from its housing. Check the polarity before trying again. Before putting the lid back in place, check that the rubber seal is in its groove. Make sure the tab is in correct position (inside the battery housing) to maintain water tightness. Screw up the 4 screws with care (do not overtighten them).
Coding of the remote control and receiver collar Each remote control has its individual radio operator code. The coding of the remote control with the receiver collar enables to couple your remote control with the receiver collar provided. IMPORTANT: before beginning the coding (first use of the receiver or re-coding), make sure no other person is using his CANICOM 200 or other products from the NUM'AXES range close by: your receiver collar could accidentally record the code of his remote control.
C button: Continuous stimulation Press the «C» button to send a warning to your dog using stimulations transmitted by two contact points located on the receiver collar, the duration will be as long as you press the button but limited to 8 seconds maximum. Nota: Beeps can be associated to the stimulations by pressing first the “C” button and then the button. « + » and « - » : control buttons Use the “+”/”-“ buttons for rapid adjustment of the stimulations level of the receiver collar.
If you have a long-haired dog and the short contact points fitted to the collar in the factory are inadequate, remove and replace them with the long ones supplied with the kit. Carefully tighten them manually (do not use a key). ● How to check that your CANICOM 200 is functioning properly You can check that your CANICOM 200 is operating correctly at any time. ▪ Before doing so, make sure that the receiver collar is turned « off ».
− Always start with beep and define the level of impulse from which your dog reacts by starting with the level of the lowest intensity and increasing gradually. − Choose the right moment to press the button: at the exact time your dog does something wrong. − Give your dog plenty of encouragement: it will learn fast and his desire to respond will only increase. ▪ Do not hesitate to contact a professional trainer for any further advice.
If you encounter any problems, re-code the receiver collar (ref. re-coding procedure). Reinitialize the system by removing the battery from its housing, then with a metallic tool (e.g. screwdriver, scissors) touch each of the 2 battery contacts for 2 seconds approximately (ref. Diagram 7). Insert the battery again: one beep is emitted, indicating the battery is in correct position. Restart your CANICOM using the remote control.
● Receiver collar battery life - 7 months in stand by: for a use of 4 hours a day 2 months in continuous use: about 10 000 stimulations of 2 seconds at level 9 To increase the battery life of the receiver collar, we recommend you to deactivate the unit if you are not using it for a long period. ● Warranty NUM’AXES guarantees the products against all manufacturing defects for 1 year after purchase.
● Collection and recycling of your device at the end of its life which appears on your product means that this one can not be thrown with The pictogram household refuse. You have to bring the device to a collection location suitable for treatment, development, recycling of electric wastes or bring it back to your distributor. Adopting this process, you do something for the environment, you contribute to the preservation of natural resources and the protection of human health. www.numaxes.
