App Cam Solo 4G PT Quick Start Guide
What’s in the Box App Cam Solo 4G PT x1 Quick Start Guide x1 Plastic Mount x1 Antenna x1 Mounting Template x1 1 Power Cable x1 Screw Kit x1
General Introduction Status LED IR LED Lens Daylight Sensor Built-in PIR Sensor Built-in Mic Nano Sim Card Slot Rotate the camera’s lens to find the reset hole, SIM card slot and SD card slot. Reset Hole Press the reset button with a pin to restore the device to factory settings.
Insert the SIM Card and SD Card 1 2 3 1. Rotate the camera lens, and remove the rubber cover. 2. Insert the SIM card. • The SIM card slot is above the SD card slot. When inserting it in, please note that gold contacts • The SD card slot is below the SIM card slot. When inserting it in, please note that gold contacts on the SD card shall face up. on the SIM card shall face down, and the trimmed corner shall be inside the camera. 3.
Tips on How to Choose the Right SIM Card 8.8mm 12.3mm Nano-Sim Required size of a nano SIM card: • The SIM card shall support WCDMA and FDD LTE. • Some SIM cards have a PIN code. Please use your smartphone to disable the PIN first. • Activate the card on your smartphone or with your network carrier before inserting it into the camera. • Please check if the camera installation area is within the selected network carrier coverage before inserting the the SIM card.
2. Wait a few seconds and a red light will be on and solid for a couple of seconds. Then it will go off. 3. A blue LED will flash for a few seconds and then go solid before going out. You will hear a voice prompt “Network connection succeeded”, which means the camera has been successfully connected to the network.
Note: You may also run into the following situations: Voice Prompt Camera Status Solutions “SIM card cannot be recognized” Camera cannot recognize this SIM card. 1. Check if the SIM card is facing the reverse direction. 2. Check if the SIM card is not fully inserted and insert it again. “The SIM card is locked with a PIN. Please disable it” Your SIM card has a PIN. Put the SIM card into your mobile phone and disable the PIN. “Not registered on network.
Charge the Battery 1. Charge the battery with a power adapter. 2. Charge the camera with Uniden solar panel. * The battery is built-in,please do not remove it from the camera * Please note that the USB charger and Solar Panel are NOT included in the package. You can buy the solar panel separately. LED Battery Status There is a status LED under the micro USB port of the camera, indicating the battery charging status.
! Important Safeguards on Rechargeable Battery Use App Cam Solo 4G PT is not designed for 24/7 full capacity running or around-the-clock live streaming. It’s designed to record motion events and remotely view live streaming only when you need it. 1. Please charge the rechargeable battery with a standard and high-quality DC 5V or 9V battery charger. 2. If you want to power the battery via the solar panel, please note that the battery is ONLY compatible with Uniden solar panel.
Install Uniden Solo App There are two ways to get the Uniden Solo App: • Search “Uniden Solo” in App Store (for iOS), download and install the app. • Search “Uniden Solo” in Google Play (for Android), download and install the app. Set up the Camera Please follow the prompt tone to configure the camera Camera has been started up. Please run app, add the camera and set it up. 1. Please click the “ ” button in the top right corner to add the camera.
3.
Attention for Camera Installation For outdoor use, please install the App Cam Solo 4G PT upside down in order to maximize the weatherproof performance and the PIR motion sensor’s efficiency. For indoor use, the camera can be placed upright, but please make sure to place it at a maximum of 2.5 meters from the ground. • PIR Sensor Detecting Distance The PIR senor has 3 range of sensitivity levels for your adjustment: Low/Mid/High. Higher sensitivity offers longer detecting distance.
• PIR Sensor Installation Angle Pease install the camera 2-3 meters above the ground. The detection range of the motion sensor would be maximized at such a height. For effective motion detection, please install the camera angularly and the angle between the PIR sensor and the detected object must be larger than 10°. Due to the limitation of PIR sensor detection, if a moving object approaches the PIR sensor vertically (the direction of the orange arrow in the image), the camera may fail to detect motion.
! Important Notes for Reducing False Alarms For reducing false alarms, please note that: • Do not install the camera facing any objects with bright lights, including sunshine, bright lamplights, etc. • Do not place the camera too close to a place where there are frequently moving vehicles. The recommended distance between the camera and the vehicle is 15 meters • Stay away from the outlets, including the air conditioner vents, humidifier outlets, the heat transfer vent of projectors, etc.
How to Install Plastic Mount Step 1 Drill holes in accordance with the mounting hole template and screw the plastic mount to the wall. If you are mounting the camera to a masonry or on any other hard surface, remember to insert the plastic anchors into the hole. NOTE: For better 4G signal strength, it is best to install the antenna upwards or horizontally. Step 2 Step 3 Install the antenna to the camera. Screw the camera to the security mount and adjust to the proper direction.
How to Mount the Camera to the Ceiling Loosen the screw on security mount and remove the ceiling bracket from the mount. 1 2 4 5 3 Install the bracket to the ceiling and attach the camera to it.
How to Attach the Camera to a Tree You are allowed to strap the camera to a tree with both the security mount and ceiling bracket. Thread the provided strap to the plate and fasten it to a tree. Next, attach the camera to the plate and you are good to go.
Troubleshooting Camera is not turning on If your camera is not turning on, please apply the following solutions: • Make sure you’ve turned the power button on. • Charge the camera with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged. PIR sensor fails to trigger alarm If the PIR sensor fails to trigger any kind of alarm within the covered area,please apply the following solutions: • On Uniden Solo App and go to Device Settings-> PIR Settings.
Specification Model Image Sensor Video Resolution Video Compression Viewing Angle Video Pan Angle Tilt Angle PIR Detecting Distance 1920 x 1080 (2.0Megapixel) 15 fps H.
Battery Power Storage Compatible Solar Panel SD Card Size Size & Weight Weight Temperature Other Parameters Humidity Waterproof Level Lithium battery/3.
WARRANTY Uniden App Cam Solo 4G PT Important: Satisfactory evidence of the original purchase is required for warranty service. Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
Parts Covered: This warranty covers the Product and included accessories. User-generated Data: This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images)that may be stored on your Product. Statement of Remedy: If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service.
THANK YOU FOR BUYING A UNIDEN PRODUCT © 2020 Uniden Australia Pty Limited V1.